812388
18
Zoom out
Zoom in
Previous page
1/23
Next page
Please pay attention to the technical information for the PWM/0-10V outputs.
Pressure monitor
In this menu, the system pressure monitoring can be activated through a direct sensor. As soon as the set pressure conditions are
undershot or exceeded, the set relay will switch on.
Pressure monitor
Relay turns on if the pressure goes below the minimum or exceeds the maximum.
RPS-Type
Type of pressure sensor
In this menu, you can adjust which pressure sensor is being used. Please note: If e.g. VFS1 is connected, RPS1 option is not shown.
Pmin
Minimum pressure. If this pressure is not met, the controller emits an error notification and the relay switches.
Pmax
Maximum pressure in the system. If this pressure is exceeded, the controller emits an error notification and the relay switches.
Sensor Calibration
Deviations in the temperature values displayed, for example. due to cables which are too long or sensors which are not positioned
optimally can be compensated for manually here. The settings can be made for each individual sensor in steps of 0.5 °C.
Settings are only necessary in special cases at the time of initial commissioning by the specialist. Incorrect measurement val-
ues can lead to unpredictable errors.
Commissioning
Starting commissioning help guides you in the correct order through the basic settings necessary for commissioning, and provides
brief descriptions of each parameter in the display. Pressing the esc‘ key takes you back to the previous value so you can look at the
selected setting again or adjust it if desired. Pressing esc‘ more than once takes you back to the selection mode, thus cancelling the
commissioning help (See " Commissioning help " on page 10).
May only be started by a specialist during commissioning! Observe the explanations for the individual parameters in these
instructions, and check whether further settings are necessary for your application.
Factory Settings
All settings can be reset, returning the controller to its delivery state.
All of the controller‘s parametrization, statistics, etc. will be lost irrevocably. The controller must then be commissioned once
again.
Time & Date
Serve to set the current time and date.
For time-dependent functions such as circulation and anti-legionella and the evaluation of system data, it is essential that
the time is accurately set on the controller. Please note that the clock continues to run for about 24 hours if the mains
voltage is interrupted, and afterward must be reset. Improper operation or an incorrect time may result in data being
cleared, recorded incorrectly or overwritten. The manufacturer accepts no liability for the recorded data!
Daylight saving time
If this function is activated, the controller automatically changes to winter time or summer time (DST, Daylight Savings Time).
18
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel SLC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel SLC in the language / languages: English as an attachment in your email.

The manual is 3.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel SLC

Sorel SLC User Manual - German - 21 pages

Sorel SLC User Manual - Dutch - 36 pages

Sorel SLC User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info