812388
8
Zoom out
Zoom in
Previous page
1/23
Next page
Wall Installation
1. Unscrew cover screw completely.
2. Carefully pull upper part of housing from lower part.
During the removal, the brackets are released as
well.
3. Set upper part of housing aside Do not touch the
electronics.
4. Hold the lower part of the housing up to the selec-
ted position and mark the three mounting holes.
Make sure that the wall surface is as even as pos-
sible so that the housing does not become distorted
when screwed on.
5. Using a drill and size 6 bit, drill three holes at the
points marked on the wall and push in the plugs.
6. Insert the upper screw and screw it in slightly.
7. Fit the upper part of the housing and insert the other
two screws.
8. Align the housing and tighten the three screws.
Electrical Connection
Before working on the unit, switch off the power supply and secure it against being switched on again! Check that there is
no power flowing! Electrical connections may only be made by a specialist and in compliance with the applicable reg-
ulations. The unit may not be put into operation if there is visible damage to the housing, e.g. cracks.
The unit may not be accessible from behind.
Low-voltage cables such as temperature sensor cables must be routed separately from mains voltage cables. Feed tem-
perature sensor cables only into the left-hand side of the unit, and mains voltage cables only into the right-hand side.
The customer must provide an all-pole disconnecting device, e.g. an emergency heating switch.
The cables being connected to the unit must not be stripped by more than 55 mm, and the cable jacket must reach into the
housing just to the other side of the strain relief.
Installing the Temperature Sensors
The controller operates with Pt1000 temperature sensors which are accurate to 1 °C, ensuring optimal control of system functions.
If desired, the sensor cables can be extended to a maximum of 30 m using a cable with a cross-section of at least 0.75
mm². Ensure there is no contact resistance! Position the sensor precisely in the area to be measured! Only use immersion,
pipe-mounted or flat-mounted sensors suitable for the specific area of application with the appropriate permissible tem-
perature range.
Low-voltage cables such as temperature sensor cables must be routed separately from mains voltage cables. Feed tem-
perature sensor cables only into the left-hand side of the unit, and mains voltage cables only into the right-hand side.
8
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel SLC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel SLC in the language / languages: English as an attachment in your email.

The manual is 3.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel SLC

Sorel SLC User Manual - German - 21 pages

Sorel SLC User Manual - Dutch - 36 pages

Sorel SLC User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info