812338
36
Zoom out
Zoom in
Previous page
1/44
Next page
Heating circuit offset
The temperature offset setting for the eco operaing mode “Lower” (see above).
Heat pump run time
The compressor turns on at least for the set time.
Heat pump idle time
The compressor is blocked for this time after it is shut down.
Heat pump delay
Delay for this function.The function first turns on after this time span if the switch conditions were reached and are still present.
This delay is intended to prevent unnecessary switching operations caused by temperature fluctuations or toGive another energy
source time to provide the necessary energy.
Storage charge pump (SLP) overshoot
The pump turns off after the compressor delayed by this time.
Bivalent temperature
Below the temperature set here, the next energy source is added.
Min. outdoor temperature
When the outdoor temperature set here is undershot, the heat pump switches off.
Periods
Approval time for the compressor function
Here the desired periods are set in which the compressor is approved. For each weekday, three times can be specified, fur-
thermore, you can copy individual day to other days. The compressor is shut down outside of the set times.
Anti Legionella
see " Anti Legionella " on page 30.
Loading pump
The function switches on the charge pump of a heat pump if a heat request from the heating circuit or DHW sensor is present.
This function can only be selected if a compressor was activated on a different relay.
Storage charge pump (SLP) overshoot
The pump turns off after the compressor delayed by this time.
Glycol pump
The glycol pump is turned on and off together with the compressor. Function is only visible if the additional function Compressor
is activated.
Gylcol pump lag
After shutting down the compressor, the pump remains on for the time set here.
Return flow increase
With this function, for example, the return temperature of a heating circuit is increased through the storage.
RF Tmin
Minimum temperature at storage sensor to enable the return flow increase. As soon as this temperature at the set storage sensor
is exceeded and adequate ΔT is present, the relay is turned on.
RL Tmax
Maximum temperature set on the storage sensor set for this function If this temperature is exceeded at the RL storage sensor, the
function is deactivated again.
36
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel LHCC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel LHCC in the language / languages: English as an attachment in your email.

The manual is 8.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel LHCC

Sorel LHCC User Manual - German - 46 pages

Sorel LHCC User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info