734406
45
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
XENON 2 FF 45 Rev.3.0
5.0 Quick Release Wheels
Quick-release axles on rear wheel
The rear wheels are equipped with quick-release axles. The wheels can then be
fitted or removed without using tools. To remove a wheel, simply depress the
quick-release button on the axle and pull the wheel off the axle. (Fig.5.1).
Quick release for quads/tetraplegics
Please flip up the release lever (1). The take out the quick release axles and/or
the wheels.
When the wheels/quick release axles have been put on the chair again, please
flip the release lever down.
Please do always ensure that the release mechanism is closed and fully locked
before starting to use the wheel chair (Fig. 5.2).
WARNING!
Hold the quick-release button on the axle depressed when inserting the axle
into the frame to mount the rear wheels. Release the button to lock the axle in
place. The quick-release button should snap back to its original position.
Risk of injury. Do not get your fingers caught in the rotating wheel. Always stop
wheel rotation before removing the wheels.
6.0 Options
6.1 Step Tubes
Step tubes are used by attendants to push a wheelchair over an obstacle.
Simply step on the tube to push a wheelchair, for example, over a kerb or step,
(Fig.6.1.1).
6.2 Wheel Locks
CAUTION!
Braking power can be affected by incorrect fitting and adjustment of the wheel
locks, as well as tyre pressure which is too low.
Wheel locks
Your wheelchair is equipped with two wheel locks. They are applied directly
against the tyres. To engage, press both wheel-lock levers forward against the
stops. To release the wheel, pull the levers back to their original positions.
Braking power will decrease with:
Worn tyre tread
Tyre pressure that is too low
Wet tyres
Improperly adjusted wheel locks.
The wheel locks have not been designed to be used as wheel locks for a moving
wheelchair. The wheel locks should therefore never be used to wheel locks a
moving wheelchair. Always use the hand rims for braking. Make sure that the
interval between the tyres and wheel locks complies with given specifications. To
readjust, loosen the screw and set the appropriate gap. Then re-tighten the
screw, (Fig.6.2.1 and Fig.6.2.2).
CAUTION!
After each adjustment of the rear wheels, check the wheel lock gap and re-adjust
if necessary.
3.0 mm
Fig. 6.2.2
Fig. 6.2.1
Fig. 6.1.1
Fig. 5.1
Fig. 5.2
1
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sopur Xenon 2 FF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sopur Xenon 2 FF in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info