543656
53
Zoom out
Zoom in
Previous page
1/68
Next page
53
Troubleshooting
Others
Warning Messages
Use the list below to check the meaning of the messages displayed on the screen.
Messages List
Message Meaning and Remedy
High temp.! Lamp off in 1
min.
The internal temperature is too high.
c Turn off the power.
c Check to see that nothing is blocking the ventilation holes.
Frequency is out of range! This input signal cannot be projected as the frequency is out of the
acceptable range of the projector.
The resolution setting of the output signal of the computer is too
high.
c Input a signal that is within the range of the frequency.
Please check Input-C
Signal Sel.
You have input an RGB signal from the computer when “Input-C
Signal Sel.” in the Setup menu is set to “Component.
c Set “Input-C Signal Sel.” correctly (see page 39).
Please replace the Lamp1
(2) and Filter.
It is time to replace the lamp and air filters.
c Replace the lamp (see page 46) and air filters (see page 48).
c Replace the specified air filters (see page 48).
If this message appears again after you replace the lamp, the lamp
replacement process is not complete.
c Check that the replaced lamp has been set properly.
To erase a message, press any key on the control panel of the
projector or on the remote commander.
Error occurred on Lamp 1
(2).
Only Lamp 2 (1) is lit.
It is time to replace the lamp.
c Replace the specified lamp (see page 46).
The lamp temperature is too high.
c Wait for more than 60 seconds so that the lamp cools, and then
turn on the power again.
Lamp 1 (2) is not set.
Please set Lamp 1 (2).
The lamp is not set.
c Set the specified lamp properly (see page 46).
Lamp Light Mode was
changed (to Auto One
Lamp mode). On next
start-up, it becomes
effective. Start up now?
V Yes v No
The lamp lighting mode has been changed.
c Restart the projector, and select whether you set it to be active
soon or not.
The projector temperature
is high. “High Altitude
Mode” should be “On” if
the projector is being used
at high altitude.
c Check to ensure that the ventilation holes on the projector are not
covered.
c When using the projector at high altitude, set the “High Altitude
Mode” to “On” (see page 38).
If the temperature inside the projector remains high, the “High
Altitude Mode” is switched to “On” in one minute, then the fan
speed increases.
Note
Note
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony VPL-FH300L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony VPL-FH300L in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info