699858
52
Zoom out
Zoom in
Previous page
1/73
Next page
Administrating the Camera
Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu
52
Sensor input Tab — Set the sensor
input 1/2/3/4
Sensor input mode
Set the direction of the detected input signal to the
sensor input terminal of the camera.
Normally open: Triggers an alarm when the sensor
input is short-circuited.
Normally closed: Triggers an alarm when the sensor
input is open-circuited.
Notes
Allow at least two seconds for the input signal to be
detected; otherwise, some events may not be detected.
When you use video streaming by SSL connection, set
as follows. Some events may not be detected if the
camera is not in the following conditions.
–Set the Bit rate below 1 Mbps.
–Set the Frame rate below 30 fps.
Use the video streaming below two transmissions at
the same time.
OK/Cancel
See “Buttons common to every menu” on page 21.
Camera tampering detection Tab —
Set the camera tampering detection
Note
Deselect the checkbox of Stabilizer in the Installation
tab of the System menu. After setting the camera
tampering detection, set the Stabilizer function again.
Enable
Select the checkbox to activate the function to detect
camera tampering, such as direction shifting or spray.
Detection status
Display the tampering detection state of the time when
Camera tampering detection tab is opened. To clear the
detection status, click Clear button.
Auto clear
Clear the detection status automatically.
Select the checkbox to set the time to be cleared
automatically. When the checkbox is not selected, the
detection status will not be cleared unless the Clear
button is pressed.
Auto clear time
Set the time from when the camera tampering detection
is detected until the detection status is cleared
automatically.
OK/Cancel
See “Buttons common to every menu” on page 21.
Motion detection Tab — Set the
motion/VMF detection
Motion detection responds to moving objects in the
camera image and triggers an alarm.
In VMF, an alarm sounds when motion is detected under
the motion detection setting, entering or passing through
a specified area or inspection line. An alarm also sounds
when an object has been left or removed from a specified
area or inspection line.
The detected object will be displayed on the monitor in
the green frame. The removed object and left object will
be displayed in the magenta frame.
Note
Perform the following before setting the motion
detection.
Deselect the checkbox of Stabilizer in the Installation
tab of the System menu.
What is VMF
VMF is a function for detecting an object entering or
passing through a specified area or inspection line, or
when an object has been left or removed from a specified
area or inspection line. Video/audio recording and/or
audio file playback can be synchronized with this alarm.
You can set the inspection methods to execute
independently. Intrusion and Passing can also be set to
execute in combination.
For example:
An alarm sounds when an object enters areas A, B and
C.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony SNC-WR632C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony SNC-WR632C in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony SNC-WR632C

Sony SNC-WR632C User Manual - German - 82 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info