Manual Sony rm vl 600 t (page 29 of 36) (English)

122744

Zoom out

Zoom in

1/36

Symptom

All Component Select buttons flash twice.

After programming the Power-On command of a

component, pressing that Component Select button does

not function correctly.

The System Control function or Control Programme

function does not work properly.

Remedy

• The Hold function is on. Unlock the Hold function (page 25).

•A Learning function has already been set on the Component Select

button. If a Learning function has been set (page 12), you can

programme the Power-On function on the Component Select button

(page 20) but the Power-On setting will not work until you clear the

“learned” function. Erase the “learned” function after setting the

Power-On function.

This function is for Sony components only.

• When you programme a System Control function or Control

Programme function, make sure to follow the correct steps (pages 21,

23).

• Change the direction the Remote Commander is aimed. If the problem

persists, position the programmed components closer together.

• If the remote control receivers of the components are too far apart, or if

something is blocking the signals between them, some of the

components may not operate in sequence even after you press the

programmed button. If some of the components do not operate

correctly because of the above or any other reason, position the

components back to the way they were before you set the System

Control function or Control Programme function. Failure to do this can

result in incorrect operation when you use these functions again.

• Some components may not always be powered on by the System

Control function or Control Programme function. This is because the

power of the component turns on and off alternately when receiving

the power on/off signal. In this case, check the operating component‘s

power on/off state before using the System Control function.

• If you change the AV brands‘ component code number (page 8) set on a

Component Select button that has been programmed for a series of

commands by the Control Programme function, the new signal will be

transmitted when you press the corresponding Component Select

button.

• The intervals between steps may be too short. Depending on the

components, you may need to insert an interval between consecutive

controls. You can insert an interval by changing the order of pressing

the buttons. (You can insert an interval between steps when

programming the Component Select button.)

• If a SYSTEM CONTROL button or a Component Select button has

already “learned” a remote control signal (page 12), you can

programme a System Control function (System Control Macro) or a

Control Programme function (Component Macro), but the function will

not work until you clear the Learned function. To clear the Learned

function, see “Changing or erasing the function of a “learned” button”

on page 16.

Customer Service

If you have any questions or

problems concerning the Remote

Commander that are not covered

in this manual, please call the

customer remote helpline. The

number is mentioned in the

warranty card.

Helpline available

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sony rm vl 600 t in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony rm vl 600 t

Sony rm vl 600 t User Manual - German, Dutch, French - 104 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sony rm vl 600 t Manual

Product: