122744

Sony rm vl 600 t Manual

28
Zoom out
Zoom in
Previous page
1/36
Next page
28
Troubleshooting
If you have problems setting up or using the Remote Commander, first check the batteries (page 6), then
check the items below.
Remedy
• Move closer to the component. The maximum operating distance is
approximately 10 m. (32.8 ft).
• Check that you are aiming the Commander directly at the component,
and that there are no obstructions between the Commander and the
component.
• Power on the components first, if necessary.
• Make sure you have pressed the correct Component Select button. In
case of MD or DAT, make sure the desired component is selected.
• Check that the component has infrared remote capability. For example,
if your component did not come with a remote commander, it probably
is not capable of being controlled by a remote commander.
• You have assigned a different component to the Component Select
button. Check the component assigned to that button and the
component code.
• If your visual components are connected to an audio system, make sure
you have set up the Commander as described in “Controlling the
Volume of Visual Components Connected to an Audio System” (page
19).
• You have assigned another component on the TV or AMP button (page
24). In this case, the volume cannot be controlled when you select
components other than a TV or AMP.
• Batteries are weakened.
Replace them with new ones.
• Set the component code correctly. If the code that is listed first for your
component does not work, try all the codes for your component in the
order in which they are listed in the supplied “Component code
numbers.”
• Some features may not be preset. If some or all of the buttons do not
function correctly even after you have set the component codes, then
use the Learning function to programme the remote control signals for
the component (page 12).
• The component may be operated with a code number that is not listed
in the “Component code numbers.” See “Setting a Component Code by
the Search Function” (page 10) and try setting a code number again
with the Search function.
• When you teach signals of an interactive signal exchange system
remote control unit (supplied with some of Sony’s amplifiers) to the
Commander, the response signal of the main unit may interfere with
the learning of the Commander. In such a case, move to a place where
the signals will not reach the main unit (e.g., another room, etc.).
• Make sure that the Remote Commander has “learned” the correct
signals. If not, see “For accurate Learning” (page 14) and try the
Learning procedure again (page 12).
• Learning has not succeeded. See “For accurate Learning” (page 14) and
try the Learning procedure again (page 12).
• There are no available buttons for “learning.” Clear infrequently used
Learned functions (page 16), then carry out learning procedure.
• The component codes cannot be set. See the supplied “Component code
numbers” and try setting the component codes again (page 8).
• A selected Component Select button or another button to be set has any
remote control signals programmed by Learning function (page 12).
Clear the “learned” signals (page 16) or select another button which has
no “learned” signals, and try setting again.
Symptom
You cannot operate components.
You cannot control the volume.
The Component Select buttons flash by a constant interval
when you press a button.
You cannot operate a component even after setting the
component code numbers.
The Commander fails to learn the remote control signals.
You cannot operate a component even after you
programmed the remote control signals with the Learning
function.
The SET indicator flashes five times during the Learning
procedure.
A Component Select button flashes five times during
setting.
The SET indicator flashes twice during the Learning
procedure.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony rm vl 600 t at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony rm vl 600 t in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony rm vl 600 t

Sony rm vl 600 t User Manual - German, Dutch, French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info