122744
22
Zoom out
Zoom in
Previous page
1/36
Next page
22
Example: To programme the procedure above to
the SYSTEM CONTROL B button
1 Press and while holding SET, press the
SYSTEM CONTROL B button.
The SET indicator light turns on.
SET
If a System Control function (System Control
Macro) has already been set on the button,
the SET indicator flashes twice.
The setting procedure is automatically cancelled.
2 Set the System Control function.
With this example, press buttons in sequence as
below:
TV
1
VCR
VCR
AMP
VIDEO1
TV
1
11
You can programme up to 16 consecutive steps
on each of the SYSTEM CONTROL buttons (A –
D), including the initial step of pressing switch
to a Component Select button.
3 Press SET to complete the programming.
The SYSTEM CONTROL button light turns off.
To programme a new series of operations for
those buttons which already have a Control
Programme set
Erase the programme (page 22).
Notes
If you interrupt the procedure at any point for over 20
seconds, the setting mode ends and the series of
commands will be programmed up to that point. In this
case, clear the programme (page 22) and start again from
Step 1 to set the entire programme from the beginning.
You cannot continue programming once the setting mode
ends.
If a SYSTEM CONTROL button has already “learned” a
remote control signal (page 12), you can programme a
System Control function (System Control Macro), but the
function will not work until you clear the Learning
function. To clear the Learning function, see “Changing
or erasing the function of a “learned” button” on page
16.
If you change the component code number (page 8) or
programme a new signal by using the Learning function
(page 12) on a key or a button that has been programmed
with a series of commands using the System Control
function, the new signal will be transmitted when you
press the corresponding SYSTEM CONTROL button.
While in setting mode, you cannot clear any operation
step you have programmed. If you have programmed an
incorrect operation by mistake, start again from Step 1.
If you try to programme more than 16 steps, the System
Control setting mode ends, and the 16 steps you have
programmed are registered. If you want to programme
the steps again, clear the programme (page 22) and start
again from Step 1.
Tips for programming the System Control
functions
The following information helps you to programme
a consecutive operation steps.
About the order of operation steps
Some of the components may not accept
consecutive remote control signals. For example,
some TVs generally may not respond to the next
signal right after the Power-on signal. So, a series of
commands such as TV Power-on and input select
may not work properly.
In this case, insert other signals to other
components, such as in the example below:
TV Power-ontVCR Power-ont VCR playback t
TV input select
To clear programmed commands
1 Press and while holding SET, press and
hold for more than 3 seconds the SYSTEM
CONTROL button you want to clear.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony rm vl 600 t at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony rm vl 600 t in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony rm vl 600 t

Sony rm vl 600 t User Manual - German, Dutch, French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info