Manual Sony rm vl 600 t (page 14 of 36) (English)

122744

Zoom out

Zoom in

1/36

If the SET indicator flashes five times

It means that “learning” is incomplete. Repeat steps 4

and 5.

6 Repeat Steps 4 and 5 to “teach” functions

to other buttons.

To “teach” another component’s remote

control signal

After positioning the two remote commanders as in

Step 1 on page 12, press the corresponding Component

Select button, and then follow Steps 4 and 5 to perform

Learning.

7 Press SET to finish setting.

Notes

• If you do not perform Learning steps within 20 seconds

at any point during the process, Learning mode ends.

• If you do not perform Step 5 within 10 seconds after Step

4, the learning procedure returns to Step 3. Repeat Step 4

while the Component Select button lights.

To cancel setup, press SET.

If the Commander does not seem to be

working

If the “learned” button does not operate properly, “teach”

once again. (For example, if the volume becomes very loud

after pressing 2 + only once, noise may have interfered

during the Learning procedure.)

If you set a component code after “learning” a

signal

If you have programmed any signal on a button by the

Learning function, that signal will work even after you set

a component code.

Note on the REC z signal

You can only “teach” to one button at a time. Therefore you

cannot teach a sequential button operation (for example

REC z + B) to a single button on the Commander. In this

case, “teach” the combined function of the buttons on your

component to the Commander.

When you “teach” signals to 2 +/– or %

•If you used the Learning

function to programme

the 2 +/–

or % buttons to send any signal to

components other than the TV or AMP, that signal

will be transmitted only by pressing 2 +/– or %

when you select that component.

•If you used the Learning

function to programme

the 2 +/–

or % buttons to send any signal to the

TV or AMP, that signal will be transmitted only

after you select TV or AMP. When you select other

components, the “learned” signal will be

transmitted.

To “teach” the signals for an

air-conditioner

See “Notes on programming the signals for an air-

conditioner” on page 18.

For accurate Learning

•Do not move the remote units during the

Learning procedure.

•Be sure to keep holding down the “learning”

button until your Commander reacts as described.

•Use fresh batteries in both remote units.

•Avoid Learning in places subject to direct sunlight

or a strong fluorescent light. (Noise may interfere

during the Learning procedure.)

•The remote control detector area may differ

depending on each remote unit. If Learning does

not work, try changing the positions of the two

remote control units.

•When you teach signals of an interactive signal

exchange system remote control unit (supplied

with some of Sony’s amplifiers) to the

Commander, the response signal of the main unit

may interfere with the learning of the

Commander. In such a case, move to a place

where the signals will not reach the main unit (e.g.

other rooms, etc.).

IMPORTANT

Be sure to place the Commander out of the reach

of small children or pets, and lock the controls

using the Hold function (page 25).

Components such as air - conditioners, heaters,

electric appliances, and electric shutters or

curtains receiving an infrared signal can be

dangerous if misused.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sony rm vl 600 t in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony rm vl 600 t

Sony rm vl 600 t User Manual - German, Dutch, French - 104 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sony rm vl 600 t Manual

Product: