157194
10
Zoom out
Zoom in
Previous page
1/31
Next page
masterpage:Left
(3 column)
lename[E:\SEM_Janet\Revision
D
ata\J9050000_4238553141MDSJE480CEL\4238553141\GB05OPE-CEL.fm]
model name1[MDS-JE480]
[4-238-553-14(1)]
10
GB
Recording tips (continued)
Marking track numbers while
recording
— Manual/Automatic Track Marking
You can mark track numbers either manually or
automatically while recording. By marking
track numbers at specific points, you can easily
locate the points later or edit the MD.
Marking track numbers manually
(Manual Track Marking)
While recording, press REC z at the point
where you want to add a track number.
Marking track numbers automatically
(Automatic Track Marking)
When recording from a CD player or MD deck
connected to a DIGITAL IN connector, the deck
marks track numbers in the same sequence as
the source. When recording from other sources
connected to the DIGITAL IN connector or a
source connected to the ANALOG IN jacks, do
the procedure below to mark track numbers
automatically. However, you cannot mark track
numbers automatically if the sound of the
source to be recorded is noisy (e.g., tapes or
radio programs).
1 While the deck is stopped, press MENU/
NO.
2 Turn AMS (or press ./>
repeatedly) until “Setup?” appears,
then press PUSH ENTER or YES.
3 Turn AMS (or press ./>
repeatedly) until “T.Mark LSyn”
appears, then press PUSH ENTER or
YES.
4 Turn AMS (or press ./>
repeatedly) to select the setting, then
press PUSH ENTER or YES.
5 Press MENU/NO.
When you set Automatic Track Marking to
on, “L.SYNC” lights up.
The deck marks a track number whenever
the input signal level drops to –50 dB
1)
(the
trigger level for Automatic Track Marking)
or below for at least 1.5 seconds.
1) Factory setting.
To change the trigger level for
Automatic Track Marking
Do the procedure below to change the signal
level that triggers Automatic Track Marking.
1 While the deck is stopped, press MENU/
NO.
2 Turn AMS (or press ./>
repeatedly) until “Setup?” appears,
then press PUSH ENTER or YES.
3 Turn AMS (or press ./>
repeatedly) until “LS(T)” appears, then
press PUSH ENTER or YES.
4 Turn AMS (or press ./>
repeatedly) to select the level, then
press PUSH ENTER or YES.
You can set the level at any value between
–72 dB and 0 dB, in 2 dB increments
(–50 dB is the factory setting).
5 Press MENU/NO.
Tips for automatic track marking
When recording from a CD player or an MD deck
connected to the DIGITAL IN connector, the entire
material might be recorded as a single track in the
following cases:
When you consecutively record the same track
two or more times using single-track repeat play.
When you consecutively record two or more
tracks with the same track number but from
different CDs or MDs.
When you record tracks from certain CD or
multi-disc players.
To Select
Turn on Automatic
Track Marking
T.Mark LSyn (factory
setting)
Turn off Automatic
Track Marking
T.Mark Off
GB02REG-CEL.book Page 10 Wednesday, July 13, 2005 2:56 PM
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony minidisc player mds je480 b at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony minidisc player mds je480 b in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info