157194
8
Zoom out
Zoom in
Previous page
1/31
Next page
masterpage:Left
(3 column)
lename[E:\SEM_Janet\Revision
D
ata\J9050000_4238553141MDSJE480CEL\4238553141\GB05OPE-CEL.fm]
8
GB
model name1[MDS-JE480]
[4-238-553-14(1)]
Recording to MDs
If the MD has been partially recorded,
recording starts after the recorded tracks.
1 Turn on the amplifier and program
source, and select the source on the
amplifier.
2 Press ?/1 to turn on the deck.
The STANDBY indicator turns off.
3 Load a recordable MD into the slot
(page 15).
4 Press INPUT repeatedly to select the
input jacks (connector) connected to
the program source.
5 Press REC z.
The deck changes to recording pause.
6 Adjust the recording level if necessary.
For details, see “Adjusting the recording
level” on page 12.
7 Press H or X.
Recording starts.
8 Start playing the program source.
Operations you may want to do
during recording
1) The track number increases by one.
Recording to an MD
When the source is
connected to the
Set INPUT to
DIGITAL OPTICAL IN
connector
D-IN
ANALOG IN jacks A-IN
To Press
Stop recording x
Pause recording X
Resume recording after
pausing
1)
H or X
Eject the MD EJECT A after stopping
recording
To change the display while
recording
Press LEVEL/DISPLAY/CHAR (or DISPLAY)
repeatedly to change the display.
Each time you press the button, the display
changes cyclically as follows:
Track number and recorded time of the current
track t Remaining recordable time
2)
on the
MD t Level of the input signal t Track
name
3)
2) Time shown in the display differs depending on
the setting of REC MODE.
3) “No Name” appears when the track has no name.
After recording
Press EJECT A to remove the MD or press
?/1 to turn off the deck.
“TOC” or “TOC Writing” starts flashing. The
TOC is updated and recording is completed.
Before disconnecting the AC power
cord
MD recording is completed when the MD Table
of Contents (TOC) is updated. The TOC is
updated when you eject the MD or press ?/1 to
turn off the deck. Do not disconnect the AC
power cord before updating the TOC (while
“TOC” is lit) or while updating the TOC (while
“TOC Writing” is flashing) to ensure a
complete recording.
Automatic conversion of digital
sampling rates
A built-in sampling rate converter automatically
converts the sampling frequency of various
digital sources to the 44.1 kHz sampling rate of
the MD deck. This allows you to monitor and
record sources such as 32 or 48 kHz DAT tape
or satellite broadcasts, as well as the CDs and
MDs.
Notes on recording
GB02REG-CEL.book Page 8 Wednesday, July 13, 2005 2:56 PM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony minidisc player mds je480 b at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony minidisc player mds je480 b in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info