680783
52
Zoom out
Zoom in
Previous page
1/88
Next page
52
S10931-00001_Rev-D_EN
INFORMATION
The specied partial opening can be
approached from any position of the door.
1. Close the door completely up to the door CLOSE
end position.
2. Press the Radio button repeatedly to select radio
channel CH 2 and to program the partial opening
function to the desired transmitter button.
3. Set DIP switch 2 on the motor carriage to "ON."
4. Press the desired button on the transmitter for the
partial opening function.
The door moves in door OPEN direction.
5. When the door reaches the desired partial opening
position, press the button on the transmitter again.
The door stops at the desired position.
The partial opening function is programmed.
10.18 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to "OFF."
2. Open the door completely up to the door OPEN end
position.
Partial opening is deleted.
To program a new position, see Chapter "10.17 Setting
partial opening."
10.19 Wicket door safety device
The wicket door safety device prevents operation of the
door with open wicket doors.
1. The wicket door safety device must be installed
so that the switch reliably detects the open door.
Do not install the wicket door safety device on the
hinge side.
2. Connect the wicket door safety device on the
terminal block on the motor carriage. The contact
command is at 12 V DC, 10 mA. The normally closed
contact is potential-free.
3. Check the function.
INFORMATION
If the wicket door is opened, the operator
lighting on the motor carriage switches
on. If the door closes, the operator lighting
lights up for the set lighting time and then
switches off. The lighting time can be
modied with SOMlink and a WiFienabled
device.
INFORMATION
If the wicket door remains open longer
than 60 minutes, the operator lighting
switches off automatically after 60 minutes.
This value can be changed via SOMlink
and a WiFi-enabled device.
INFORMATION
If the control unit receives a new command
with the wicket door open, the LEDs of the
operator lighting change from permanent
to ashing light.
10.20 12 V output
The use of the 12 V output depends on the version of the
motor carriage circuit board.
This output can be used for the power supply of external
accessories. Two operating modes are available. 12 V DC,
max. 100 mA are available for them.
8K2
+12V
br
gn
wh
+12V
OSE
8
K
b
r
g
n
+
12
V
O
S
E
Fig. 12 V output
Operating mode 1 (factory setting)
Power supply for external devices, for example finger
scanners mounted in the door panel.
INFORMATION
Power-saving mode must be deactivated
for this operating mode. Set DIP switch
3 on the wall control unit to "ON."
See chapter "13.4 Power-saving mode."
Operating mode 2 (external lighting)
In this operating mode, external lighting can be
connected and switched via the CH 2 radio channel,
for example lighting with LEDs. This operating mode
can only be activated via SOMlink and a WiFi-enabled
device.
In the "External lighting" operating mode, the OSE/8K2
safety device can no longer be used on the motor
carriage.
INFORMATION
If the "External lighting" operating mode
is used, the operator lighting works with
reduced illumination power.
10. Connections and special functions of the motor
carriage
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9110 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9110 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9110 pro

Sommer S 9110 pro User Manual - German - 88 pages

Sommer S 9110 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info