680556
51
Zoom out
Zoom in
Previous page
1/80
Next page
51
46900V001_Rev-D_EN
11. Connections and special functions of the ceiling
control unit
11.3 Setting the DIP switches on the
ceiling control unit
Special functions can be set with the DIP switches on the
ceiling control unit.
All DIP switches are set to OFF by default.
NOTE
Do not use a metal object to set the
DIP switches, because this may damage
the DIP switches or the circuit board.
Use a suitable tool to set the DIP switches,
such as a at, thin plastic object.
DIP switches
on the ceiling
control unit ON
OFF
1
ON
1
23
4
"Conex"
additional
circuit board
T1denes
door OPEN
T2denes
door CLOSE
"Conex"
additional
circuit board
T1 pulse
sequence
T2 lighting
function/partial
opening
2
ON
1234
Relay
(MUFU) trips
during door
movement
and if the door
is not closed*
Relay (MUFU)
lighting
function
3
ON
1234
Continuous
power to the
complete
system
activated
Power-
saving mode
activated
4
ON
1234
COM and
Signal
activated
as button
input (partial
opening)
COM and
Signal
activated as
safety contact
for photocell
* e.g.: door status display
11.4 Button 2 for partial opening
If required, another button can be connected for partial
opening operation. After installation of the keypad, all
settings must be made on the ceiling control unit and the
motor carriage.
NOTE
The control unit cover is connected to the
circuit board of the ceiling control unit via
a connection cable. If an accumulator has
been installed, it is also connected to the
circuit board.
Carefully remove the control unit cover
and disconnect the connections to prevent
damage to the ceiling control unit.
INFORMATION
If button 2 (partial opening) is used,
a photocell cannot be connected.
The automatic closing operating mode is
then not possible.
Installing the keypad
1. When installing the potential-free keypad, select a
suitable position at a height of at least 1.6 m.
2. Install the keypad.
3. The keyboard cable for the ceiling control unit must
be firmly secured to prevent displacement.
Installation of the control cable and settings on the
ceiling control unit
1. Disconnect the operator from the mains voltage.
Check that the operator is disconnected from the
power supply.
2. Unscrew the cover from the ceiling control unit.
3. If an accumulator is used, it must also be
disconnected, see Chapter "11.11 Installing and
removing the accumulator".
4. Remove the control unit cover.
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
G
N
D
+24
V
ON
1234
Fig. 5 Fig. 6
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9110 base plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9110 base plus in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9110 base plus

Sommer S 9110 base plus Installation Guide - German - 80 pages

Sommer S 9110 base plus Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info