Manual Sommer S 9080 pro (page 78 of 88) (English)

680782

Zoom out

Zoom in

1/88

S10931-00001_Rev-D_EN

16. Troubleshooting

16.4 Troubleshooting table

Problem Possible cause Test/check Remedy

The operator opens

the door when the

transmitter or command

device is actuated but

does not close it.

• Photocell and safety

device interrupted

• Check photocell and safety

devices

• Remove obstacle

• The photocell must be aligned

• If necessary, have it checked and

replacedbyaqualiedspecialist

• Automatic closing

function activated

• Wait to see whether the

operator starts automatically

after 30 seconds

• Automatic closing function

deactivated

• Have the cause corrected by

a trained electrician

Operator cannot be

operated with the

command device.

• No power • Check power supply • Check the power outlet with

a different device, for example

by plugging in a lamp

• Limit switch on motor

carriage defective

• Unlock operator and push

motor carriage to the centre

of the track

• Lock operator

• Actuate transmitter

• If the operator still closes

thedoor but does not open it,

the limit switch is defective

• Have the limit switch replaced by

aqualiedspecialist

• The operator was

unlocked by the

emergency release

mechanism

• Check that the door can be

moved manually

• Pull the emergency release handle

to lock the operator

• Control device

incorrectly connected to

the operator

• Check function of operator

with a transmitter

• Check wiring and correct if

necessary

• Membrane keypad

of the wall unit is not

working

• Check cable • Plug in cable

• If necessary, replace wall control

unit cover

• Transmitter defective • Operator cannot be started

with the transmitter

• Check transmitter power supply

• If necessary, replace the battery

of the transmitter

• If necessary, replace the

transmitter with a new one

• Operator defective • Operator cannot be started

with the transmitter or the

connected command device

• Have operator repaired or

replacedbyaqualiedspecialist

• Electrical supply voltage

outside the approved

range

• Have the mains voltage

checked by a trained

electrician

• Have the cause corrected by

a trained electrician

When a button on the

transmitter is pressed,

the operator does not

open or close the door.

• Transmitter not

programmed

• Radio LED does not light

up when the transmitter is

operated

• Programme transmitter

• Battery in the

transmitterisat

• Replace the battery of the

transmitter

• Transmitter defective • LED on transmitter does not

light up

• Replace transmitter

Radio command cannot

be programmed

• Memory full • AllfourLEDsforradioash

cyclically for about 3 seconds

• Memory full, see Chapter

"10.6 Information on Memo"

and "10.8 Deleting a transmitter

button from the radio channel"

MEMOIdentiererror

• Incorrect MEMO • AllfourLEDsforradioash

cyclically for a short time and

then go out for a long time.

The operator lighting of the

motorcarriageashes4times

short and 4 times long.

• Disconnect operator from the

power supply, unplug Memo,

re-supply operator with power

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sommer S 9080 pro Manual

Product: