680782
49
Zoom out
Zoom in
Previous page
1/88
Next page
49
S10931-00001_Rev-D_EN
10. Connections and special functions of the motor
carriage
10.12 Programming a second handheld
transmitter by radio (HFL)
Prerequisites for programming by radio
A handheld transmitter must already be programmed
on the radio receiver. The handheld transmitters used
must be identical. For example, a Pearl can only be
programmed on a Pearl and a Pearl Vibe on a Pearl Vibe.
The button assignment of handheld transmitter (A) that
put the radio receiver into programming mode by radio
is used for the new handheld transmitter (B) that is to
be programmed. The already-programmed handheld
transmitter and the new handheld transmitter to be
programmed must be situated in the range of the radio
receiver.
Example:
1. Button 1 has been programmed to radio channel
1 and button 2 to radio channel 2 by handheld
transmitter (A).
The newly-programmed transmitter (B) adopts
the button assignment of transmitter (A): Button 1
to radio channel 1 and button 2 to channel 2.
Restriction
The following setting is not possible:
targeted programming of a selected handheld
transmitter button to a radio channel
1
2
A
3
B
Fig. 1
1. Press buttons 1 + 2 of a programmed handheld
transmitter (A) for 3 - 5 seconds until the LED on
the handheld transmitter briefly light up.
Theoperatorlightingashes.
2. Release buttons 1 and 2 of handheld transmitter (A).
If no radio command is transmitted within another
30 seconds, the radio receiver switches over to
normal mode.
3. Press any button, e.g. (3) on the new handheld
transmitter (B) to be programmed.
The LEDs of the operator lighting remain steady.
Second handheld transmitter (B) has been
programmed.
10.13 Performing a reset
15 s1 s 5 s 10 s
Reset of the
safety inputs
Force values
deleted
Position
values and
frame photo
eye deleted
Settings
restored
Fig. Overview of the time sequence of the motor carriage status
LED when the green Reset button is pressed
RADIO
RESET
CH1
CH2
CH3
CH4
STATUS
ON
1
2
3
4
Fig. 1
INFORMATION
A SOMlink and a WiFi-enabled device
are required to reset all parameters to
the factory settings.
Resetting the safety devices
1. Press the green Reset button for 1 second.
Reset of the connected safety devices.
Subsequently attached safety devices are
detected.
Deleting the force values
1. Press the green Reset button on the motor carriage
for 5 seconds until the green status LED flashes
slowly.
Force values are deleted.
Deleting force and position values
1. Press the green Reset button on the motor carriage
for 10 seconds until the green status LED flashes
quickly.
Force and position values deleted.
Frame photocell deleted.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info