680782
51
Zoom out
Zoom in
Previous page
1/88
Next page
51
S10931-00001_Rev-D_EN
10. Connections and special functions of the motor
carriage
1. Close the door.
2. Set DIP switch 1 to "ON” position.
3. The pre-set hold open time of the door is 30
seconds.
Every new command within these 30 seconds
restarts the hold open time. The door OPEN position
is reached by pressing button 1 on the transmitter.
The door movement cannot be stopped with the
transmitter.
4. The door closes automatically after 30 seconds.
The closing movement can be stopped by
a command with the transmitter.
Door opens completely - after reversal of direction.
5. The door starts the closing process again after
30 seconds.
Door CLOSE.
INFORMATION
The factory setting is fully automatic
closing with a pre-set hold open time
of 30 seconds from the door OPEN end
position and 60 seconds from partial
opening.
When driving through, the photocell
is activated, and the hold open time
is shortened to 5 seconds for sectional
doors and side-opening sectional doors.
This setting and the selection of semi-
automatic closing can be adjusted via
SOMlink and a WiFi-enabled device.
INFORMATION
The pre-warning time can be activated and
adjusted via SOMlink and a WiFi-enabled
device.
The progress of the pre-warning time is
displayed by the ashing operator lighting
and the warning light.
10.16 Setting the lighting function
The operator lighting on the motor carriage can be
switched on and off separately via radio channel CH 2.
This function is pre-set in the factory settings.
Program the desired handheld transmitter button to radio
channel CH 2.
The factory setting of DIP switch 2 is "OFF," and the
lighting function is therefore activated.
INFORMATION
The lighting function or partial opening
can be operated.
1. Set DIP switch 2 on the motor carriage to "OFF."
2. Press the Radio button repeatedly to select the radio
channel CH 2. Program the lighting function on the
desired transmitter button.
The lighting function is available.
The operator lighting can now be switched on and off
with the corresponding transmitter button.
INFORMATION
If the operator lighting is not switched off
manually, it switches off automatically after
60 minutes. This value can be changed via
SOMlink and a WiFi-enabled device.
Other lights and functions are available with the
accessories Lumi pro
+
or Relay.
The Lumi pro
+
is an LED strip with 12 LEDs (24 V, 4 W).
It can be attached to the wall control unit as supplemental
lighting.
The relay (potential-free changeover contact) is
pluggable and can be attached to the wall control unit.
It can be used for controlling external lighting such as
garage lights or courtyard lights. The maximum switching
capacity is 5 A/AC 250 V or 5 A/DC 24 V.
Parallel to the operator lighting, the Lumi pro+ and the
relay switch on with the "Start" impulse. The lighting time
set at the factory is 180 seconds. If the light function
is activated via the CH 2 radio channel, the operator
lighting, the Lumi pro+ and the relay can also be switched
on and off separately. This does not trigger a travel
command. After 60 minutes, the operator lighting, the
Lumi pro
+
or the relay are switched off automatically.
The Lumi pro
+
and the relay accessories can be
purchased from your specialist dealer or at:
www.sommer.eu
10.17 Setting partial opening
This function allows you to set a desired partial opening.
The door then does not open completely, but only to the
set door position.
Example:
A side-opening sectional door can be opened to allow
a person to pass through. The partial opening function
can be used via radio control system or button 2,
see chapter "11.5 Button 2 for partial opening."
INFORMATION
The lighting function or partial opening
can be operated.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info