680825
68
Zoom out
Zoom in
Previous page
1/96
Next page
68
S10564-00001_Rev-A_EN
12. Function test/Final test
12.1 Testing obstacle detection
Observe in particular the following safety instructions for
this chapter.
After commissioning the operator, the force measurement
of the operator must be checked with a force
measurement device and an obstacle recognition test
must be performed.
WARNING
Danger of entrapment!
If the force setting is too high, persons
or animals in the movement area of the
door may be trapped and pulled along
with the door.
Severe injuries or death may result.
The force setting is relevant to safety
and must be carefully checked and
if necessary adjusted by qualied
specialists.
WARNING
Danger of crushing and shearing!
If the door moves with persons or
animals in the movement area, crushing
and shearing injuries may be caused
by the mechanism and safety edges of
the door.
The power cut-off does not operate
below 50 mm.
The photo eye function must be tested
once a month.
Only use the operator in direct view of
the door.
All danger zones must be visible during
the entire door operation.
Always keep the moving door in sight.
Persons or animals must not be in the
range of movement of the door.
Never put your hand near the door
or moving parts when it is moving.
In particular, do not reach into the
moving push arm.
Do not reach into the ceiling mounting
unit when the carriage runs along the
track.
Only pass through the door only once
it is completely open and the trafc light
has given access authorisation.
NOTE
Observe the national standards, guidelines
and regulations for cut-off of the operating
forces.
NOTE
The obstacle detection must be tested
once a month to prevent damage to the
operator.
INFORMATION
After installation of the operator, the
person responsible for the installation
of the operator must complete an
EC Declaration of Conformity for the door
system in accordance with Machinery
Directive 2006/42/EC and apply the
CE mark and a type plate to the door
system. This also applies if the operator
is retrotted to a manually operated door.
All documents as well as the inspection
book for the door, the installation and
operating manual and the handover
protocol must be retained by the user.
INFORMATION
Reversing: The operator stops on contact
with an obstacle and then moves a bit
in the opposite direction to release the
obstacle.
In the automatic closing function the
door opens completely if an obstacle is
detected.
INFORMATION
The operating forces can be modied
and adjusted with SOMlink and a WLAN-
enabled device. For more information ask
your specialist dealer.
After successful testing of the force settings, the obstacle
recognition and the functions, the qualified specialist
must attach the CE mark and type place on the door
system.
The operator must reverse in the door OPEN direction
when it is loaded with a weight of 20 kg. The weight is
fastened in the centre of the bottom edge of the door for
this purpose.
The door must immediately stop and reverse during the
door CLOSE movement if it hits a 50-mm-high obstacle.
1. Open the door with the operator.
2. Place a 50-mm-high object in the centre of the door.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga

Sommer S 9060 Tiga User Manual - German - 96 pages

Sommer S 9060 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info