680825
55
Zoom out
Zoom in
Previous page
1/96
Next page
55
S10564-00001_Rev-A_EN
10. Connections and special functions of the carriage
8K2
+12V
br
gn
wh
+12V
OSE
8
K
b
r
g
n
+
12
V
O
S
E
K
2
E
Fig. Output 12 V
Terminal block Function
br = +12 V DC Output 12 V DC,
max. 100 mA
wh = GND
External consumers can be connected in this operating
mode, for example a finger scanner on the door panel. In
this operating mode, power-saving mode is not available
and must be deactivated, see Chapter "13.5 Power-
saving mode".
INFORMATION
Power-saving mode must be deactivated
for this operating mode. Set DIP switch 3
on the wall control unit to ON.
10.22 Setting partial opening
A desired door opening can be selected with this
function, e.g. for access for persons. The door does not
open completely, but only to the set door OPEN end
position.
INFORMATION
The specied partial opening can be from
any position of the door.
INFORMATION
The automatic closing function can also
be activated in order to program the partial
opening function.
INFORMATION
When the door has reached the partial
opening position, the trafc lights light up
red on both sides of the door.
1. Close the door completely up to the door CLOSE
end position.
2. Press the radio button repeatedly to select radio
channel CH 2 and to program the partial opening
function to the desired transmitter button.
3. Set DIP switch 2 on the carriage to ON.
4. Press the desired button on the transmitter for the
partial opening function.
The door moves in door OPEN direction.
5. When the desired partial opening position has been
reached, press the button on the transmitter.
The door stops at the desired position.
6. Press the button on the transmitter again.
7. The door moves to the door CLOSE end position.
The partial opening function is programmed.
10.23 Deleting partial opening
1. Set DIP switch 2 on the carriage to OFF.
2. Open the door completely up to the door OPEN end
position.
Partial opening is deleted.
To program a new position see Chapter "10.22 Setting
partial opening".
10.24 Slip door safety device
The slip door safety device prevents operation of the
door with open slip doors.
1. The slip door safety device must be installed so that
the switch reliably detects the open door. Do not
install the slip door safety device on the hinge side.
Also see the separate "Slip door" installation
instructions.
2. Connect the slip door safety device on the terminal
block on the carriage. The contact command is at
12 V DC, 10 mA. The normally closed contact is
potential-neutral.
3. Check the slip door safety device function.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga

Sommer S 9060 Tiga User Manual - German - 96 pages

Sommer S 9060 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info