680828
79
Zoom out
Zoom in
Previous page
1/100
Next page
79
S10557-00001_Rev-A_EN
13. Operation
Fig. 7
7. After the door CLOSE end position has been reached,
all traffic lights on both sides are switched off.
Both sides: Trafc lights off.
13.4 Obstacle detection
The operator stops and reverses slightly if it encounters
an obstacle. This prevent injury and damage to property.
The door will be partially of completely opened depending
on the setting. The partial reversal is pre-set at the
factory. A full reversal can be set with SOMlink and a
smartphone.
INFORMATION
In the automatic closing function the door
opens completely.
INFORMATION
If the photo eye is interrupted, the door
runs on for a long distance.
The following safety devices are installed to detect
obstacles:
Photo eye (object protection)
Safety contact strips (personal protection)
Force cut-off of operator (personal protection)
For more, also note Chapter "14. Maintenance and care".
Force cut-off in door OPEN direction of motion
Operator stops, reverses a bit in door OPEN
direction and stops.
Operator expects a new command and does not
start automatically.
After receiving a command, the operator moves in
the door OPEN direction.
Force cut-off in door CLOSE direction of motion with
automatic closing function
Operator stops and reverses to the door OPEN
end position after encountering an obstacle.
The door closes automatically after the open
holding time.
INFORMATION
If the door encounters an obstacle again
in the door CLOSE direction, the operator
stops and reverses completely to the door
OPEN end position. The door stays there.
The automatic closing function is
interrupted. The open holding time and
clearing time do not start again until a
command for door CLOSE.
The door is then automatically closed.
Alarm
If the ALARM safety input is open, a command for
opening the door system is triggered:
The potential-neutral NC contact, for example, is suitable
for a fire alarm system.
Operator starts from door CLOSE end position,
drives to door OPEN end position and stays there.
Green trafc light for the interior and red trafc light
for the exterior start to ash quickly.
Incoming commands are not executed.
NOTE
The door system and the operator must
be checked before resetting the ALARM
safety input. All damages must be repaired
without delay.
Resetting the ALARM safety input
1. Disconnect the operator from the mains voltage.
Check it is disconnected from the power supply.
2. Check door system and operator for damage and
repair.
3. Reset fire alarm system (close contact).
4. Connect the operator to the mains voltage.
Check that the power supply is connected.
5. Execute a command using the button.
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 Tiga plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 Tiga plus in the language / languages: English as an attachment in your email.

The manual is 10,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 Tiga plus

Sommer S 9060 Tiga plus User Manual - German - 100 pages

Sommer S 9060 Tiga plus User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info