680551
46
Zoom out
Zoom in
Previous page
1/80
Next page
46
46900V001_Rev-D_EN
10. Connections and special functions of the motor
carriage
INFORMATION
The lighting function or partial opening can
be operated.
1. Set DIP switch 2 on the motor carriage to OFF.
2. Press the radio button repeatedly to select the radio
channel CH 2. Programme the lighting function on
the desired transmitter button.
The lighting function is available.
The operator lighting on the motor carriage can be
switched on and off with the transmitter button.
INFORMATION
If the operator lighting is not switched off
manually, it switches off automatically after
60 minutes. This value can be changed via
SOMlink and a WiFi-enabled device.
Other lights and functions are available with the Lumi
+
and the relay accessories.
The Lumi
+
is an LED strip with 12 LEDs (24V, 7W). It can
be attached to the ceiling control unit as supplemental
lighting.
Parallel to the operator lighting, the Lumi+ and relay
switch on with the "Start" impulse. The light burning time
set at the factory is 180 seconds. If the light function
is activated via the CH 2 radio channel, the operator
lighting, the Lumi+ and the relay can also be switched
on and off separately. This does not trigger a travel
command.
After 60 minutes, the operator lighting, the Lumi
+
or the
relay are switched off automatically.
The Lumi
+
and the relay accessories can be purchased
from your specialist dealer or at:
www.sommer.eu
10.17 Setting partial opening
This function allows you to set a desired partial opening.
The door then does not open completely, but only to the
set door position.
Example:
A side-opening sectional door can be opened to allow a
person to pass through. The partial opening can only be
used via radio control system or button 2, see Chapter
"11.4 Button 2 for partial opening".
INFORMATION
The specied partial opening can be from
any position of the door.
INFORMATION
A partial opening function can only be
programmed with automatic closing
deactivated.
1. Close the door completely up to the door CLOSE
end position.
2. Press the radio button repeatedly to select radio
channel CH 2 and to program the partial opening
function to the desired transmitter button.
3. Set DIP switch 2 on the motor carriage to ON.
4. Press the desired button on the transmitter for the
partial opening function.
The door moves in door OPEN direction.
5. When the door reaches the desired partial opening
position, press the button on the transmitter again.
The door stops at the desired position.
10.18 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to OFF.
2. Open the door completely up to the door OPEN end
position.
Partial opening is deleted.
To program a new position, see Chapter "10.17 Setting
partial opening".
10.19 Wicket door safety device
The wicket door safety device prevents operation of the
door with open wicket doors.
1. The wicket door safety device must be installed
so that the switch reliably detects the open door.
Do not install the wicket door safety device on the
hinge side.
2. Connect the wicket door safety device on the
terminal block on the motor carriage. The contact
command is at 12 V DC, 10 mA. The normally closed
contact is potential-free.
3. Check the function.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 base at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 base in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 base

Sommer S 9060 base Installation Guide - German - 80 pages

Sommer S 9060 base Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info