680551
45
Zoom out
Zoom in
Previous page
1/80
Next page
45
46900V001_Rev-D_EN
10. Connections and special functions of the motor
carriage
10.15 Setting automatic closing function -
defining basic values
When automatic closing is activated, the door is opened
by a pulse.
The door moves to the door OPEN end position.
The door closes automatically after the hold open time.
With the factory settings, the door also closes
automatically from the partial opening position when
the automatic closing function is activated.
WARNING
Risk of injury during automatic
closing!
Automatically closing doors can injure
people and animals in the movement
area of the door when the door is
closing. This may cause serious or fatal
injury.
Always keep the moving door in sight.
Keep persons and animals clear of the
range of movement of the door.
Never put your hand near the door
when it is moving or near moving parts.
In particular, do not reach into the
ceiling holder or the push arm.
Do not drive through the door until it has
opened completely.
NOTE
If the door is not in view and the operator is
actuated, objects in the movement area of
the door may be jammed and damaged.
Objects must not be in the range of
movement of the door.
INFORMATION
The door opens completely if it hits an
obstacle.
INFORMATION
Operation with automatic closing must
comply with EN 12453. This is a legal
requirement. National regulations must be
observed in non-European countries.
A photocell must be connected. Bridging
the safety inputs with wire bridges is not
permitted.
1. Close the door.
2. Set DIP switch 1 to ON.
3. The hold open time of the door is 30 seconds.
Every new command within 30 seconds restarts
the hold open time. If button 1 on the transmitter is
pressed, the door moves to door OPEN end position.
The door movement cannot be stopped with the
transmitter.
4. The door closes automatically after 30 seconds.
The closing movement can be stopped by a
command with the transmitter.
Door opens completely - after reversal of direction.
5. The door starts the closing process again after
30 seconds.
Door CLOSE.
INFORMATION
The factory setting is fully automatic
closing with a preset hold open time of
30 seconds from the door OPEN end
position and 60 seconds from partial
opening.
When driving through, the photocell
is activated and the hold open time is
shortened to 5 seconds for sectional doors
and side-opening sectional doors.
This setting and the selection of semi-
automatic closing can be set via SOMlink
and a WiFi-enabled device.
INFORMATION
The pre-warning time can be activated and
adjusted via SOMlink and a WiFi-enabled
device.
The progress of the pre-warning time is
displayed by the ashing operator lighting
and the warning light.
10.16 Setting the lighting function
The operator lighting on the motor carriage can be
switched on and off separately via radio channel CH 2.
This function is pre-set in the factory settings.
Program the desired handheld transmitter button on radio
channel CH 2.
The factory setting of DIP switch 2 is OFF, and the
lighting function is therefore activated.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 base at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 base in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 base

Sommer S 9060 base Installation Guide - German - 80 pages

Sommer S 9060 base Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info