655955
61
Zoom out
Zoom in
Previous page
1/160
Next page
Preparing for use
ENGLISH 21
The power tool is delivered for operation of the cut-off wheel in the centre position by default. Generally,
the power tool is more balanced in the centre position, because the weight is distributed symmetrically to
the centre axis and the cut therefore is easier to guide.
If obstacles are very close to the cutting location, it may be required to install the cutting device in the outer
position so that the cut-off wheel is located farther towards the outside.
When working with the cut-off wheel in the outer position, observe the asymmetric weight
distribution! If possible, work in the centre position.
Conversion from centre to outer position
Preparation
x Put the power tool on level ground.
x Remove the cut-off wheel: Î Chap. 5.3,
page 17
x Remove the water supply line (30):
Unscrew the attachment screw (a) of the water
supply line on the right and left sides of the
wheel guard (2).
Remove both adapter pieces (b) including the
line from the wheel guard. Put down adapter
pieces including line so that the line does not
interfere with the following work steps and is not
clamped.
x Remove handle for wheel guard adjustment (3).
Loosen both attachment screws (c) of the handle
for wheel guard adjustment and remove the
handle.
x Loosen both attachment nuts (d) of the ribbed
belt cover (14).
x Turn ribbed belt tension screw (13) towards the
left, e.g. counter-clockwise, to reduce the ribbed
belt tension.
Turn until the square nut (e) has been moved
towards the mark "" (f) as far as possible.
When installing the cutting device in the centre
position (cf. figure), the square nut is all the way
to the left; in case of installation in the outer
position, it is located all the way to the right.
x Remove both attachment nuts (d) entirely.
x Remove the ribbed belt cover (14).
Remove wheel guard (2)
x Carefully move the wheel guard towards the
motor unit. The screws (g) of the assembly
flange (j) are moved within the oblong holes.
x Once the wheel guard has been moved towards
the motor unit until the ribbed belt support (i) can
be pulled through the ribbed belt (h), remove the
wheel guard. Observe that the ribbed belt is not
damaged by this.
5.8 Relocate cutting device from centre position to outer position
2
3
30
a
b
c
e
14
f
d
13
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 879 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 879 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info