488766

Solac IDEAL 1000 PROFESIONAL Mod FL6410 Manual

11
Zoom out
Zoom in
Previous page
1/66
Next page
11
en
USE WITH SOLID FAT
7 Gently lower the basket into the fryer and place it in frying position (fig.
b). When the food is placed inside the fryer the pilot light will switch on,
since the food causes the oil to cool due to the temperature difference,
and it will switch off again when the oil reaches the temperature indicated
on the temperature regulating control.
Z The food should always be covered by the oil.
8 Close the lid (1) on the fryer to prevent fumes and smells.
9 After frying the food, open the deep fryer lid, lift out the basket and shake
it gently. Next, hook it into the draining position (fig. C) for the food to
drain off as much oil as possible.
10 Once the food is drained, take the basket out of the deep fryer and empty
it.
11 Put the temperature control (3) in the 0 position. Then unplug the
appliance from the mains.
12 Once the oil has cooled, place the basket inside the deep fryer and put
the handle in the position shown in fig. D. If you were using solid fat,
leave it to solidify in the vat and store the deep fryer with the fat in it.
4 USE WITH SOLID FAT
Z If you use solid fat for frying (when not previously used), you must take
the following precautions:
1 Melt the pieces of new solid frying fat in a pan at a low heat. Watch over
the pan at all times and keep it out of the reach of children.
2 Turn off the heat as soon as the fat has melted. Place the deep fryer in
the kitchen sink and very carefully pour the melted fat into the vat.
i Remember not to go over the maximum level indicated in the vat.
3 If you are going to use fat that is in the deep fryer left over from a
previous frying session, make holes in the fat with the help of a fork.
4 Close the deep fryer lid to avoid spatters and turn the temperature
regulating control (3) to 150o so that the fat slowly softens. If you wish,
you can increase the temperature once the fat has melted.
FL6410.book Page 11 Thursday, June 25, 2009 5:06 PM
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solac IDEAL 1000 PROFESIONAL Mod FL6410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solac IDEAL 1000 PROFESIONAL Mod FL6410 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info