619731

Snooper STP1400 Tyre Pilot Manual

7
Zoom out
Zoom in
Previous page
1/9
Next page
Sensor Low Voltage Alarm
If one of the sensors battery becomes discharged it will send a signal to the user
interface. Alarm (Bi..Bi..Bi...) sounds for 10 seconds, and alarm icon , will flash.
Pressure reading and icon will flash alternatively ( flash 3 second, pressure
reading flash 5 seconds). Those flashing icon can only be stopped when sensor
battery was replaced.
e.g. left front tyre battery low was detected, monitor alarm display as shown:
Custom ID Coding
The STP1400 is shipped with 4 sensors re-coded into the display, however should
you need to replace a sensor please follow these instructions. Below is Inflation
Code Learning to re-code the sensors ID:
Inflate Code Learning
1. In standby mode, quickly press SET button 5 times and release it after the
Bi... sound to enter learning mode, the Left Front digits will flash on the LCD.
2. Short press SET once to scroll tyre position needed to re-code. Once ready, then
mount the sensor on to the tyre valve, once the sensor sensed the inflation, the
sensor will send its own ID code to the monitor and the monitor will display the
sensor code after the Bi... sound. Repeat above step to re-code others sensor if
needed .
3. If the ID code was NOT detected, system will keep the old code unchanged.
4. Any new ID code will overwrite the old ID code when detected.
5. IMPORTANT press SET until Bi... sound to ensure the new code saved into the
monitor.
12 • UK
Low battery icon flashing
Alarm icon flashing
6. During learning mode if no key was press for one minutes, the system will
resume to standby operation without saving any changes.
Sensors Installation
The sensors are pre-configured for each tyre location marked tyre position with:
LF, LR, RF, RR with stickers. IMPORTANT: Please ensure the correct ‘marked’ sensor
is fitted to corresponding tyre.
External Sensors Installation
13 • UK
Corresponding tyre display flashing
User tip: Please mount sensors based on Factory default position.
User tip: Please be sure to turn the monitor ON first before installing a sensor.
Please note:
1. Each sensor are labelled with its wheel position.
2.
If the battery inside sensor has insufficient voltage it will trigger battery low alarm.
3. After all sensor has been installed, please check that there is no air leakage.
LF
LR
RF
RR
Mount the hex nuts Check if locking
cover is in place
Screw in sensor at
clock wise direction
Tighten hex nuts in
counter clock wise
direction
1 2
3
4
Hex nut
Air valve Sensor
Hex nut
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snooper STP1400 Tyre Pilot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snooper STP1400 Tyre Pilot in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info