809890
70
Zoom out
Zoom in
Previous page
1/76
Next page
70
v1.01
Admin and Installation Guide M400 Description of Settings
Setting Description
System (Fig. 1 and 2)
Base station name In multicell setup: IP address and - if set - name assigned to base station in
Management settings
Operation/duration D-H:M:S Operation: Time since last reboot ((days–hours:minutes:seconds)
Duration
DECT operation D-H:M:S How long the base station has been running (days–hours:minutes:seconds)
Busy The number of times the base station has been busy
Busy duration The total time the base station has been busy for speech (8 or more calls
active)
SIP failed The number of times SIP registrations have failed
Handset removed The number of times handsets have been marked as removed
Searching The number of times the base station has searched for its sync source
Free Running The number of times the base station has been free-running
DECT source changed The number of times the base station has changed its sync source
Calls (Fig. 3)
Base station name In multicell setup: IP address and - if set - name assigned to base station in
Management settings
Operation duration Operation: Time since last reboot

Count Number of calls on base station
Dropped Number of active calls that were dropped for reasons like handset moving out
of range etc. An entry is stored in the syslog.
No response Number of active calls that weren't answered, for example because handset
was out of range etc. An entry is stored in the syslog.
Duration The total time that calls were active on the base station.
Active The total number of active calls on the base station (DECT and non-DECT
calls). There can be up to 8 calls on a base station in a multicell installation,
and up to 10 active calls on a single-cell base station.
Max active The maximum number of calls that have been active at the same time.
Codec Logging and count of codecs used on each call.
Handover success The number of successfull handovers
Handover failed The number of failed handovers
Audio not detected Number of incidents
Repeater (Fig. 4)
Idx/name Idx and - if set - name assigned to repeater in Repeaters settings
Operation Total operation time since last reboot or reset.
Busy The number of times the repeater was busy.
Busy duration The total time that the repeater was been busy for speech (5 or more calls
active).
Max active The maximum number of calls that have been active at the same time.
Searching The number of times the repeater has searched for its sync source.
Recovery When the repeater has lost its sync source, it will attempt to lock onto another
base station or repeater. Statistics show recovery mode.
DECT source changed The number of times the repeater has changed its sync source.
Wideband The number of wideband calls on repeaters
Narrowband The number of narrowband calls on repeaters
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snom M400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snom M400 in the language / languages: English as an attachment in your email.

The manual is 2.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info