809886
13
Zoom out
Zoom in
Previous page
1/120
Next page
13
v1.01
M200SC Administrator and Provisioning Manual Configuration using the phone menus
2. Press q or p to highlight your network type (IPv4 or IPv6), and then press MENU/SELECT. The selected
network type screen appears.
IPv4
-Mode (DHCP, Static IP, PPPoE, Disabled)
-Set static IP
-Set static DNS
-Set PPPoE (Point-to-Point Protocol over Ethernet)
IPv6
-Mode (Disabled, Auto, Static IP)
-Set static IP
-Set static DNS
VLAN ID
-WAN port (enabled/disabled, default disabled)
-VID: (range 0-7, default 0)
-Priority (range 0-9, default 0)
DHCP (IPv4) or Auto (IPv6) is enabled by default, which means the M200SC will get its IP address from the
network. When DHCP and Auto are disabled, you must enter a static IP address, the subnet mask, gateway,
and the IP addresses of the primary and secondary DNS server manually.
Note: You must be familiar with TCP/IP principles and protocols to configure static IP settings.
Setting Description
Mode (IPv4
& IPv6)
DHCP (default) When DHCP is enabled, static IP, static DNS and PPOE cannot be edited.
Static IP When DHCP is not available or disabled, this submenu is available for
manual setting of IP address, subnet mask, gateway, IP addresses of
primary and secondary DNS server.
Set static IP (IPv4 & IPv6)
Set static DNS When DHCP is not available or disabled, this submenu is available to
enable/disable static DNS and to set the IP addresses of the primary and
secondary DNS server.
Set PPOE (IPv4) Point-to-Point Protocol over Ethernet
Setting static IP
1. From the Mode menu (Fig. 4, above), press the MENU key to select Static IP, and then press SET. If
DHCP is disabled, the Set static IP menu appears. If DHCP is enabled, an error message appears briefly
before returning you to the Network setting menu.
2. On the Set static IP menu, enter the static IP address. Use the dial pad to enter characters. To add a period,
press the * key.
SAVE
0.0.0.0
Set static IP
Subnet Mask:
0.0.0.0
IP Address:
3. Press q and enter the Subnet Mask. Use the dial pad to enter characters.
4. Press q and enter the Gateway. Use the dial pad to enter characters.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snom M200 SC Base Station at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snom M200 SC Base Station in the language / languages: English as an attachment in your email.

The manual is 4.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info