791163
57
Zoom out
Zoom in
Previous page
1/66
Next page
CLEANING AND MAINTENANCE - 12991477A327/B
e
4. Touch the START button to start filling
the reservoir of the appliance with the
descaling solution.
5. In the end, shake the loading nozzle to
remove any remaining water.
6. Place the loading nozzle place in its
housing.
7. Remove the jug (or container).
Boiler descaling function
1. Close the door
2. Descaling starts.
At the end of the descaling process the display
shows the request to drain the water softener.
Reservoir draining
1. Open the door
2. Place a jug or a container on the open
door.
3. Pull the loading nozzle out of its housing.
4. Press the START button to start draining
the water softener into the jug (or container).
The descaling solution begins to flow into the
jug.
5. Wait for the end of the drain flow.
6. Empty the descaling solution in the jug (or
container).
Cleaning the reservoir and hydraulic circuit
Once the water softener has been drained, the
appliance starts the cleaning procedure for the
reservoir and the hydraulic circuit.
The display will show the request to fill the
reservoir with water.
1. Fill a jug or container with about 2 litres of
clean water.
2. Open the oven door.
3. Place the jug (or container) on the open
door.
4. Pull the loading nozzle out of its housing.
5. Place the end of the tube at the bottom of
the jug (or container).
6. Press the START button to start filling the
appliance reservoir with water.
7. When you have finished filling water into the
reservoir, touch the CONFIRM button
to continue with the function.
The appliance starts the function using the
parameters set.
When cleaning the tank and the hydraulic
circuit, leave the jug on the door open with
the filling nozzle inside. The appliance
cyclically discharges certain quantities of
water used for cleaning.
During this process, the overflowing of water
inside the oven cavity is not intended as a
malfunction, rather it is part of the rinsing
procedure.
8. At the end of the cleaning process, the
display indicates the request to drain water.
9. Clean and dry any residual water inside the
oven cavity.
10.Open the door
11.Place a jug or a container on the open
door.
12.Pull the loading nozzle out of its housing.
13. Press the START button to start draining
the water into the jug (or container).
14.Wait for the end of the drain flow.
When complete, the display will indicate that
the residual water removal process is complete.
Manual descaling
When you wish to perform descaling in
advance, you can run the function manually:
1. Touch the OTHER FUNCTIONS
button on the "main menu" (in the main area
).
Take care: the descaling solution may
be still hot.
Use cold tap water which is not too
hard, softened water or still mineral
water.
Do not use distilled water, tap water
with a high chloride content (> 40 mg/
l), or other liquids.
The overflowing of water inside the
oven cavity is not intended as a
malfunction, rather it is part of the rinsing
procedure.
Function that performs descaling of
boiler.
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg SO4104 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg SO4104 in the language / languages: English as an attachment in your email.

The manual is 2.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info