490939

Skytec TEC 350 Manual

7
Zoom out
Zoom in
Previous page
1/17
Next page
Connections and Controls
MIC channel
The input of the mono microphone channel is via an XLR/jack connector (6) on the top left side of the
panel. See diagram below for the different possible connections. The MIC slider control (7) sets the
level of the microphone signal. The TALKOVER switch (8) reduces the sound level of the channels A
to D to ensure that the microphone signal is audible over the music.
Channels 1 to 3
These three stereo channels are identical. Every input accepts a CD player or a turntable via RCA
phono sockets (21) on the rear panel. The channels feature a 2-band tone control (3&4) and a selector
switch for turntable or CD player operation (2).
Channel 4
This channel has a stereo line input (19) (CD, cassette deck or another mixer) and a 6.3mm mono
input for an extra microphone (20).
Crossfader
This slider controls allows to fade between two of the channels A to D. Example: Set the left ASSIGN
knob (11) to A and the right ASIGN knob to D. If you push the crossfader (12) completely to the left,
you will only hear the sound of channel A. If you push it completely to the right, only channel D will be
heard. You can set any combination of the two ASSIGN knobs. The slider controls of the two selected
channels must of course be pushed upwards.
Master section
The MASTER slider control (10) sets the total output level to the amplifier. The level is indicated on the
LED vu-meter (9). Set the level to a point where the red LEDs only light up very shortly in order to
avoid overdrive. The RCA phono output to be connected to the amplifier is on the rear panel and
marked MASTER (18). The adjacent socket marked ‘REC’ (17) is for connection of the output signal to
a cassette recorder.
Headphone section
Connect a stereo headphone via a 6.3mm jack plug (15). Select one of the 5 input channels or the
MASTER output channel via the rotary knob (13). Set the volume via the LEVEL knob (14).
Power ON
After having connected the audio sources to the mixer and the mixer to the amplifier, set all slider
controls to the lowest position. Only then switch on the mixer and the amplifier.
Replacement of the crossfader
Due to the intensive use of this control, it needs replacement after some time. This is very easy and
requires no soldering. Remove the two screws on the panel of the crossfader via a crosshead
screwdriver. Lift off the control from the mixer and disconnect it. Push the connector on the new
crossfader (this can only be done one way). Insert the crossfader panel back into the mixer and fasten
the two screws.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytec TEC 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytec TEC 350 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info