617556
130
Zoom out
Zoom in
Previous page
1/160
Next page
General information
Read and observe on page 127 first.
For your own safety and the safety of your passengers, the following instruc-
tions must be observed before carrying out a wheel repair on the road.
Switch on the hazard warning lights system.
Place the warning triangle at the prescribed distance.
Park the vehicle as far away as possible from the flowing traffic.
Choose a location with a flat, solid surface.
Haveall the occupants get out. The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
The breakdown kit must not be used under the following circumstances.
The rim is damaged.
The outside temperature is below -20 ° C.
The cut or puncture is larger than 4 mm.
The tyre wall is damaged.
After the expiration date (see inflation bottle).
Preparations for using the breakdown kit
Read and observe
on page 127 first.
The following preparatory work must be carried out before using the puncture
repair kit.
Switch off the engine.
For vehicles with manual transmission select 1st gear .
For vehicles with
automated gearbox shift the lever to position D or R.
Firmly apply the handbrake.
Check that you can carry out the repairs with the breakdown kit » page 127.
Remove the breakdown kit from the boot.
Stick the sticker
1
» Fig. 124 on page 127 on the dash panel in the driver's
field of view.
Unscrew the valve cap.
Use the valve remover
2
to unscrew the valve core and place it on a clean
surface (rag, paper, etc.).
Sealing and inflating the tyre
Read and observe on page 127 first.
Sealing
Forcefully shake the tyre inflator bottle
10
» Fig. 124 on page 127 several
times.
Firmly screw the inflation hose
3
onto the tyre inflater bottle
10
. The film
on the cap is pierced automatically.
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
Remove the filler plug from the tyre valve.
Screw the valve core back into the tyre valve using the valve remover
2
.
Inflating
Screw the air compressor tyre inflation hose
8
» Fig. 124 on page 127 firmly
onto the tyre valve.
For vehicles with manual transmission the lever into the neutral position.
For vehicles with automated manual transmission shift the lever to position
N.
Check that the air release valve
6
is closed.
Start the engine and run it in idle.
Plug the connector
4
into 12 volt socket » page 61, 12-Volt power outlet.
Switch on the air compressor with the ON and OFF switch
9
.
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes » .
Switch off the air compressor.
If you cannot reach an air pressure of 2.0 - 2.5 bar, unscrew the tyre inflation
hose
8
from the tyre valve.
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent
to “distribute” in the tyre.
Firmly screw the tyre inflation hose
8
back onto the tyre valve and repeat
the inflation process.
Switch off the air compressor.
Remove the tyre inflation hose
8
from the tyre valve.
Once a tyre inflation pressure of 2.0 - 2.5 bar has been achieved, you can con-
tinue the journey.
128
Do-it-yourself
130


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skoda Citigo - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skoda Citigo - 2016 in the language / languages: English as an attachment in your email.

The manual is 24,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skoda Citigo - 2016

Skoda Citigo - 2016 User Manual - German - 168 pages

Skoda Citigo - 2016 User Manual - Dutch - 168 pages

Skoda Citigo - 2016 User Manual - French - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info