617556
128
Zoom out
Zoom in
Previous page
1/160
Next page
The mounting points are located on the metal bar of the lower sill on the un-
derside of your vehicle. The positions of these are embossed by means of
markings on the side surface of the lower sill » Fig. 122.
Support the base plate of the jack with its full area resting on level ground
and ensure that the jack is located in a vertical position at the jacking point
» Fig. 123 -
.
Position the lifting jack below the jacking point with the crank and move it up
until its claw encloses the web » Fig. 123 -
.
Continue turning up the jack until the wheel is just about lifted off the
ground.
WARNING
If the wheel has to be changed on a slope, first of all block the opposite
wheel with a stone or similar object to prevent the vehicle from unexpect-
edly rolling away.
Secure the base plate of the lifting jack with suitable means to prevent
possible moving. A soft and slippery ground under the base plate may move
the lifting jack, causing the vehicle to fall down. It is therefore always nec-
essary to place the lifting jack on a solid surface or use a wide and stable
base. If the surface is smooth, such as on cobbled stones, tiled floor etc.,
use a non-slip base (e.g. a rubber foot mat).
Only attach the lifting jack to the attachment points provided for this pur-
pose.
Always raise the vehicle with the doors closed.
Never position any body parts, such as arms or legs under the vehicle,
while the vehicle is raised with a lifting jack.
When the vehicle is raised, never start the engine.
CAUTION
It is important to ensure that the jack is correctly attached to the web of the
lower fork leg - risk of damage to the vehicle.
Remove the wheel / fix
When changing a wheel, the following instructions must be followed.
Remove the full wheel trim or the caps of the wheel bolts.
First of all slacken the anti-theft wheel bolt and then the other wheel bolts.
Jack up the vehicle until the wheel that needs changing is clear of the
ground.
Unscrew the wheel bolts and place them on a clean surface (cloth, paper,
etc.).
Remove the wheel carefully.
Attach the wheel and slightly screw on the wheel bolts.
Lower the vehicle.
Alternately tighten wheel bolts opposite (diagonally) with the wheel wrench.
Tighten the anti-theft wheel bolt last.
Replace the wheel trim or the caps.
When fitting unidirectional tyres, ensure that the direction of rotation is cor-
rect » page 119.
All bolts must be clean and must turn easily.
If it is established when changing a wheel that the wheel bolts are corroded
and difficult to move, then these must be replaced.
Under no circumstances grease or oil the wheel bolts!
WARNING
Undo the wheel bolts only a little (about one turn) provided that the vehicle
has not yet been jacked up. Otherwise the wheel could become loose and
fall off.
Follow-up work
After changing the wheel, the following work must be carried out.
Stow the replaced wheel in the wheel well and secure it with a special nut.
Stow the tool kit in the space provided and secure using the band.
Check the tyre pressure on the fitted wheel as soon as possible.
Have the tightening torque of the wheel bolts checked with a torque wrench
as soon as possible.
After changing the wheel, the tyre pressure should be adjusted. In vehicles
with tyre pressure monitoring, save tyre pressure values» page 91.
Replace the damaged wheel or consult a specialist garage about repair op-
tions.
The prescribed tightening torque of the wheel bolts is 110 Nm.
126
Do-it-yourself
128


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skoda Citigo - 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skoda Citigo - 2016 in the language / languages: English as an attachment in your email.

The manual is 24,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skoda Citigo - 2016

Skoda Citigo - 2016 User Manual - German - 168 pages

Skoda Citigo - 2016 User Manual - Dutch - 168 pages

Skoda Citigo - 2016 User Manual - French - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info