390795
5
Zoom out
Zoom in
Previous page
1/48
Next page
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it
Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/off locking switch H 7
- switch on tool 7a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 7b
- unlock switch/switch off tool 7c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots J 6 clear and uncovered
APPLICATION ADVICE
Instead of flange E 6 the CLIC quick-clamping flange
K 6 (SKIL accessory 2610388766) can be used;
grinding/cutting discs can then be mounted without the
use of accessory keys
GUARANTEE / ENVIRONMENT
Always keep tool and cord clean (especially the
ventilation slots)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Dispose of the tool by sorting tool, accessories and
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
INTRODUCTION
Cet outil sert au meulage, au tronçonnage et à
l'ébarbage de pièces en métal et en pierre sans utiliser
de l'eau; combiné avec des accessoires spécifiques, cet
outil peut également servir au brossage et au ponçage
SPECIFICATIONS TECHNIQUES 1
SECURITE
GENERALITES
Lire et conserver ce manuel d'instruction (faire en
particulier très attention aux instructions de sécurité au
dos de ce manuel) 2
Utiliser uniquement cet outil pour le meulage et le
tronçonnage à sec
Utiliser uniquement les brides livrées avec l'outil
Cet outil est interdit aux jeunes n'ayant pas atteint l'âge
de 16 ans
Toujours débrancher l’outil avec tout réglage ou
changement d’accessoire
ACCESSOIRES
Utiliser les accessoires d'origine SKIL en vente chez
votre concessionnaire SKIL
Pour le montage et l'utilisation d'accessoires n'étant pas
de la marque SKIL, observer les instructions du fabricant
concerné
La vitesse admissible des accessoires utilisées doit être
au moins aussi élevée que la vitesse à vide maximale de
loutil
N'utiliser jamais de disques de meulage/tronçonnage
endommagés, déformés ou vibrants
Traiter et stocker les disques de meulage/tronçonnage
avec précaution pour éviter de les endommager
Protéger les accessoires contre les impacts, les chocs et
la graisse
Ne pas utiliser une dimension de disques à
meuler/tronçonner autre que le diamètre recommandé
Utiliser uniquement les disques de meulage/tronçonnage
dont l'orifice s'adapte parfaitement à la bride de montage
D 6; n'utilisez jamais de réducteurs ni d'adaptateurs
pour ajuster des disques ayant un orifice plus grand
Ne jamais utiliser de disques de meulage/tronçonnage
ayant un orifice fileté dont le filet n'est pas suffisamment
longue pour recevoir la longueur de larbre de l'outil
Ne jamais utiliser d'accessoires avec un orifice fileté
borgne plus petit que M14 x 21 mm
UTILISATION A L'EXTERIEUR
Brancher l'outil par l'intermédiaire d'un coupe-circuit (FI)
avec courant de réaction de 30 mA au maximum
5
XP SKIL 9160/9165/9170/9175.2 17-06-2003 10:37 Pagina 5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 9170 ha at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 9170 ha in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info