Manual Skil 9170 ha (page 4 of 48) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

390795

Zoom out

Zoom in

1/48

INTRODUCTION

● This tool is intended for grinding, cutting and deburring

metal and stone materials without the use of water; with

the appropriate accessories the tool can also be used for

brushing and sanding

TECHNICAL SPECIFICATIONS 1

SAFETY

GENERAL

● Read and save this instruction manual (pay special

attention to the safety instructions at the back) 2

● Only use this tool for dry grinding/cutting

● Only use the flanges which are supplied with this tool

● This tool should not be used by people under the age of

16 years

● Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

● Use the original SKIL accessories which can be obtained

from your SKIL dealer

● For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

● Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

● Do not use damaged, deformed or vibrating

grinding/cutting discs

● Handle and store grinding/cutting discs carefully to avoid

chipping and cracking

● Protect accessories from impact, shock and grease

● Do not use a grinding/cutting disc that is larger than the

maximum recommended size

● Only use grinding/cutting discs with a hole diameter which

fits mounting flange D 6 without play; never use reducors

or adaptors to fit large-hole grinding/cutting discs

● Never use grinding/cutting discs with a threaded hole, of

which the thread is not long enough to accept the spindle

length of the tool

● Never use accessories with a "blind" threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

● Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

● Only use an extension cord which is intended for outdour

use and equipped with a splashproof coupling-socket

BEFORE USE

● Before using the tool for the first time, it is recommended

to receive practical information

● Do not work with materials containing asbestos

● Be careful of hidden electrical wires or gas- and water

pipes; check the work area, for instance with a metal

detector

● Be careful when cutting groves, especially in supporting

walls (slots in supporting walls are subject to country-

specific regulations; these regulations are to be observed

under all circumstances, so before beginning work,

consult with the responsible structural engineer, architect

or construction supervisor)

● Clamp the workpiece in case it does not remain

stationary from its own weight

● Do not clamp the tool in a vice

● Use completely unrolled and safe extension cords with a

capacity of 16 Amps (UK 13 Amps)

● Wear protective glasses and gloves, hearing protection 3,

a dust mask, and sturdy shoes; when necessary, also wear

an apron

● Always mount auxiliary handle A 6 and protective guard

B 6; never use the tool without them

● Be sure tool is switched off when plugging in

DURING USE

● Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

● If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug;

never use the tool with a damaged cord

● Push spindle-lock button G 6 only when spindle C 6 is

at a standstill

● Keep hands away from rotating accessories

● When grinding metal, sparks are generated; keep other

persons and combustible material from work area

● In case of electrical or mechanical malfunction,

immediately switch off the tool and disconnect the plug

● In case the cutting disc is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

● In case of current interruption or when the plug is

accidentally pulled out, unlock the on/off switch

immediately and put it in the OFF-position in order to

prevent uncontrolled restarting

● Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

● Before you put down the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

● After switching off the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

● Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

● If for any reason the old plug is cut off the cord of this tool,

it must be disposed of safely and not left unattended

USE

● Mount auxiliary handle A 4

● Mount protective guard B 5

! ensure that the closed side of the protective guard

always points to the operator

● Mounting of accessories 6

! disconnect the plug

- clean spindle C and all parts to be mounted

- tighten clamping flange E with spanner F while

pushing spindle-lock button G

- for removing accessories handle vice-versa

! grinding/cutting discs become very hot during use;

do not touch them until they have cooled down

! always mount backing pad when using sanding

accessories

XP SKIL 9160/9165/9170/9175.2 17-06-2003 10:37 Pagina 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 9170 ha in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 9170 ha Manual

Product: