701673
11
Zoom out
Zoom in
Previous page
1/168
Next page
11
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
Mounting of accessories
6
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping ange B with spanner C while pushing
spindle-lock button D
! 
at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it (if provided)
Mounting of auxiliary handle E
7
! disconnect the plug
- screw auxiliary handle E on the right, the top, or the left
of the tool (depending on the work to be carried out)
Removing/mounting/adjusting of protective guard F
8
! disconnect the plug
- open protective guard F by loosening screw G (do not
remove it)
- place protective guard F on the spindle collar of the tool
head and turn it to the required position (depending on
the work to be carried out)
! ensure that the closed side of the protective guard
always points to the operator
- fasten protective guard F by tightening screw G
! 
Before using the tool
- ensure that accessory is correctly mounted and rmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/o locking switch K
9
- switch on tool
9
a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch
9
b
- unlock switch/switch o tool
9
c
! 
the workpiece
! the accessory continues to rotate for a short time

Grinding
q
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting
w
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on tool
head, in order to prevent the tool from being pushed out
of the cut in an uncontrolled manner
OUTDOOR USE
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
Before using the tool for the rst time, it is recommended
to receive practical information
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Always mount auxiliary handle E
6
and protective guard
F
6
; never use the tool without them

or call the local utility company for assistance
(contact with electric lines can lead to re or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
materials you want to work with
Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specic regulations; these regulations are to be observed
under all circumstances)
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
Do not clamp the tool in a vice
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
an after-sales service centre for SKIL power tools and
carried out by a qualied person
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
In case of current interruption or when the plug
is accidentally pulled out, the tool will not restart

switch
9
c and switch on tool again
AFTER USE
After switching o the tool, never stop the rotation of the
accessory by a lateral force applied against it
EXPLANATION OF SYMBOLS ON TOOL
2
Read the instruction manual before use
3
Wear protective glasses and hearing protection
4
Double insulation (no earth wire required)
5
Do not dispose of the tool together with household waste
material
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 9006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 9006 in the language / languages: All languages as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info