758639
10
Zoom out
Zoom in
Previous page
1/92
Next page
10
- mount 4 casters D as illustrated
- the appliance is ready for dry vacuum cleaning with
cartridge lter E pre-installed
- place motor head back onto container and secure it
into place by using both latches A
- mount vacuum hose F onto hose connection G and
screw it into place
- insert extension tubes H and handle J rmly into each
other and connect them to the vacuum hose
- mount desired nozzle K, L or M onto suction tube
On/o 5
- set switch N to position “I” to start wet or dry
vacuum cleaning
- set switch N to position “O” for switching o the
vacuum cleaner
- when connecting a power tool directly to the vacuum
cleaner, universal power tool adapter P may be used
(if needed)
Airow control 6
Control the airow by sliding regulator Q up or down the
opening in handle J
Mounting/removing of cartridge lter 7
! disconnect the plug
- mount/remove cartridge lter E as illustrated
- mount protection lter R over cartridge lter E for
prolonging its service life and easy cleaning purposes
Dry vacuum cleaning 8
! ensure that all information mentioned in the
chapter “SAFETY” is read and understood
! inform yourself beforehand about the handling of
materials that are hazardous to one’s health
- verify that cartridge lter E 3 and protection lter R 3
are securely mounted
- insert dust bag S as illustrated (when using a dust bag,
cartridge lter E 3 clogs slower, the vacuuming
performance is kept longer and the disposal of dust
becomes easier)
- only vacuum directly in the container when materials
not hazardous to one’s health are being vacuumed
- switch o the appliance and disconnect the plug
after vacuuming
Wet vacuum cleaning 9
! ensure that all information mentioned in the
chapter “SAFETY” is read and understood
! inform yourself beforehand about the handling of
materials that are hazardous to one’s health
! remove dust bag S, cartridge filter E and
protection filter R before starting wet vacuuming
- ensure that container C 3 is emptied and clean
- carefully mount foam sleeve lter T as illustrated
- secure motor head back on the container, mount
desired nozzle directly onto vacuum hose or extension
tube, and switch on the appliance
- do not immerse the nozzle completely in the liquid;
leave a gap at the nozzle opening to allow air inow
- when the container reaches its maximum capacity, the
motor speed increases
- when this happens, switch o the appliance,
disconnect the plug, and empty the container 0
- switch o the appliance and disconnect the plug
after vacuuming
- clean and dry the inside and outside of the container
before storage 0
Mounting/removing of HEPA lter !
! disconnect the plug
- unlock lter door X as illustrated and pull it out
- remove HEPA lter Z and clean it or mount a new one
- insert tabs of lter door X into upper slots and lock it
into place
Storage of tubes and nozzles @
MAINTENANCE / SERVICE
Always disconnect plug from power source before
cleaning and/or maintenance
Store the appliance indoors in a dry place
Keep appliance clean (especially ventilation slots V 3)
- clean ventilation slots V 3 regularly with a brush or
compressed air
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
Cleaning of cartridge lter #
- regularly clean the carefully removed cartridge lter by
gently tapping or brushing dirt o (wear dust mask)
- do not clean indoors in living areas
! do not wash filter with soap and water
- for picking up dust the cartridge lter needs to be dry
- if the cartridge lter is wet, it will clog quickly and be
very dicult to clean
- handle the cartridge lter carefully when removing,
cleaning or replacing it
! do not use a cartridge filter with tears or small
holes; replace it immediately
Cleaning of foam sleeve lter $
- wash lter with mild soap and water and rinse it with
clean water
- allow lter to dry before mounting it again
Cleaning of HEPA lter %
- clean lter by brushing dirt o (wear dust mask)
- for optimal performance mount a new lter (for
ordering see “Service” on www.skilmasters.com)
If the appliance should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the appliance undismantled together with proof
of purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the appliance are listed on www.skilmasters.com)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or
service station)
! switch off the tool and disconnect the plug before
investigating the problem
Appliance does not operate
- no power supply -> check power supply (power cable,
circuit breakers, fuses)
- faulty power cable -> unplug and check power cable; if
damaged, have it repaired by a professional
- container full -> empty container
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 8700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8700 in the language / languages: All languages as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info