758586
14
Zoom out
Zoom in
Previous page
1/188
Next page
14
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT


waste material (only for EU countries)
-in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
-symbol 6 will remind you of this when the need for
disposing occurs
! 

NOISE / VIBRATION
Measured in accordance with EN 62841 the sound
pressure level of this tool is 91.5 dB(A) and the sound
power level 102.5 dB(A) (uncertainty K = 3 dB), and the
vibration (triax vector sum; uncertainty K = 1.5 m/s²)
cutting wood < 2.5 m/s²
The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
-using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
-the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! 


patterns
b

 3550
INTRODUCTION
Cet outil est conçu pour eectuer dans le bois des
coupes droites longitudinales et transversales ainsi que
des angles d’onglet jusqu’à 50°
Cet outil n’est pas conçu pour un usage professionnel
Lisez et conservez ce manuel d’instruction 3
CARACTERISTIQUES TECHNIQUES 1
LED-light V e automatically lights on when activating
switch Y
Battery protection
Switches o the tool or prevents the tool from being
switched on, when
-the load is too high
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
-the lithium-ion battery is nearly empty (to protect
against deep discharge)
! 

damaged
APPLICATION ADVICE
Always face the good side of the workpiece down to
ensure minimum splintering
Only use sharp saw blades of the correct type r
-quality of cut improves by the number of teeth
-carbide tipped blades stay sharp up to 30 times longer
than ordinary blades
Parallel guide Z t
-for making exact cuts along a workpiece edge
-can be inserted in either side of foot
Adjusting parallel guide
-loosen knob AA
-adjust to desired cutting width by using parallel guide
scale (use line-of-cut indicator Q as 0-reference)
-tighten knob AA
Plunge cutting y
-set desired cutting depth
-tilt tool forward with line-of-cut indicator Q lined up with
desired line of cut marked on the workpiece
-open lower guard F with lever G
-just before blade enters workpiece, switch on tool and
gradually lower back end of tool using front end of foot
as hinge-point
-gradually move tool downward as well as forward
-as soon as blade enters the material, release lever G
! 
Cutting large panels u
-support panel close to the cut either on oor, table or
workbench
! 
and not through support
-in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the right side of the foot against
this guide i
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots AB )
! 
Always keep the area around lower guard F 2 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
Clean saw blade immediately after use (especially from
resin and glue)
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3550 in the language / languages: All languages as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info