758586
13
Zoom out
Zoom in
Previous page
1/188
Next page
13
-raise/lower foot K until desired cutting depth is set on
scale using indicator L
-tighten knob J
Battery level indicator 8
-press the battery level indicator button AC to show the
current battery level.
Adjusting cutting angle (0-50°) 9
-loosen knob M
-tilt tool until desired cutting angle is set on scale using
indicator N
-tighten knob M
! 
correspond with value on cutting depth scale
90° Cutting angle check 9
-adjust and tighten foot K to maximum cutting depth 7
-adjust and tighten cutting angle to 0°
-check for a 90° angle between the blade and bottom of
foot with a square
-if adjustment is needed, loosen knob M and use
adjustment screw P as illustrated
Line-of-cut indicator Q q
-for guiding tool along desired line of cut marked on the
workpiece
-for a straight 0° cut or a 45° bevel cut use the indicator
line concerned
! the wide part of the foot should rest on the

! 

! 
cut
Dust suction w
For using vacuum cleaner
-connect vacuum cleaner hose to vacuum cleaner
adapter R
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
Dust bag
-mount dust bag AD
Operating the tool
-mount battery
-always hold handle S rmly with one hand and handle T
rmly with the other hand
-place tool with front end of foot at on workpiece
! ensure that the saw teeth are not engaged into the

-switch on tool by rst pressing knob W (= safety switch
which cannot be locked) and then pulling trigger Y
! 

-lower guard F opens automatically when saw blade
enters the workpiece (open lower guard manually by
using lever G only for special cuts such as plunge cuts)
! 

tips)
! 
coloured grip area(s)
-after completing the cut switch o tool by releasing
trigger Y
! 


After switching o your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
BATTERIES
(to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
rst time)

this tool
-SKIL battery: BR1*31****
-SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! 
provided with the charger
Removing/installing the battery 2
Mounting saw blade 2
! 
-take hex key A from storage B
-push spindle-lock button C and hold it while
you remove blade bolt D by turning hex key A
COUNTERCLOCKWISE (= in same direction as arrow
printed on saw blade)
! 
standstill
-release spindle-lock button C
-remove ange E
! 

-open lower guard F with lever G and hold it while you
mount saw blade with saw teeth and arrow printed on
saw blade pointing in same direction as arrow on upper
guard
-release lower guard F
-mount ange E
-push spindle-lock button C and hold it while you
tighten blade bolt with hex key 1/8 turn past nger tight
(ensures slippage of saw blade when it encounters
excessive resistance thus reducing motor overload and
saw kickback)
-release spindle-lock button C
Adjusting cutting depth (0-61 mm) 7
-for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
-loosen knob J
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3550 in the language / languages: All languages as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info