758357
17
Zoom out
Zoom in
Previous page
1/52
Next page
17.
Maintenance
To reduce the risk of injury, turn
power switch “OFF” and remove
plug from the power source outlet before main-
taining or lubricating your Scroll Saw.
GENERAL
Frequently blow out any dust that may accumu-
late inside the motor.
An occasional coat of paste wax on the work table
will allow the wood being cut to glide smoothly
across the work surface.
Certain cleaning agents and sol-
vents damage plastic parts.
Including: gasoline, carbon tetrachloride, chlori-
nated cleaning solvents, ammonia and household
detergents that contain ammonia. Avoiding use of
these and other types of cleaning agents mini-
mizes the probability of damage.
To avoid shock or fire hazard, if the
power cord is worn, cut or damaged in
any way, have it replaced immediately.
All repairs, electrical or mechanical,
should be attempted only by trained
repairmen. Contact the nearest Skil Factory Service
Center, Authorized Skil Service Station or other com-
petent repair service. Use only Skil replacement parts;
any other may create a hazard.
Lubrication
ARM BEARINGS
Lubricate the arm bearings with oil after 10 hours of
use. Re-oil after every 50 hours of use or whenever
there is a squeak coming from the bearings.
TO LUBRICATE
1. Remove the two rubber bearing covers.
2. Turn saw on its side as shown in (Fig. 21).
3. Squirt a generous amount of SAE 20 oil around the
shaft end and bronze bearing.
4. Let the oil soak in overnight in this condition.
5. Next day repeat the above procedure for the oppo-
site side of the saw.
Use only recommended accessories. Follow instruc-
tions that accompany accessories. Use of improper
accessories may cause hazards. See page 12 for
details on recommended accessories.
Maintaining Your Scroll Saw
Troubleshooting
WARNING
!
CAUTION
!
FIG. 21
WARNING
!
WARNING
!
Turn switch “OFF” and always remove plug
from the power source before trouble
shooting.
TROUBLE: SAW WILL NOT START
PROBLEM 1. Power cord is not plugged in.
2. Fuse or circuit breaker tripped.
3. Cord damaged.
4. Burned out switch.
REMEDY 1. Plug saw in.
2. Replace fuse or reset tripped circuit breaker.
3. Have cord replaced by an Authorized Skil
Service Center or Service Station.
4. Have switch replaced by an Authorized Skil
Service Center or Service Station.
TROUBLE: BLADE DOES NOT COME UP TO SPEED
PROBLEM 1. Extension cord too light or too long.
2. Low house voltage.
REMEDY 1. Replace with adequate cord.
2. Contact your electric company.
WARNING
!
SM 2610957121 05-08 6/5/08 7:35 AM Page 17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 3335-01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 3335-01 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info