Manual Skil 2148 (page 6 of 128) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

479914

Zoom out

Zoom in

1/128

• In case of electrical or mechanical

malfunction, immediately switch off

the tool or unplug charger from power

source

• SKIL can assure ﬂ awless functioning

of the tool only when original

accessories are used

• The tool/charger is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision or

instruction concerning use of the tool/

charger by a person responsible for

their safety

• Ensure that children do not play with

the tool/charger

• Be careful not to drive into areas

where electrical wires may be

contacted

• Ensure that switch B 2 is in the

middle (locking) position before

making any adjustments or changing

accessories as well as when carrying

or storing the tool

CHARGING/BATTERIES

• Charge battery only with the charger

that is supplied with the tool

• Do not expose tool/charger to rain

• Never charge battery outdoors 4

• Store tool/charger in locations where

temperature will not exceed 40°C or

drop below 0°C

• Batteries may explode when disposed

of in ﬁ re, so do not burn battery for

any reason

• Do not use charger when cord or plug

is damaged; cord or plug should be

replaced immediately at one of the

ofﬁ cially registered SKIL Service

Stations

• Do not disassemble charger or tool

• Do not attempt to recharge non-

rechargeable batteries

USE

• Charging battery 5

- battery of new tools is not fully

charged

- after approximately 5 hours the

battery is fully charged

! unplug the charger from the tool

after charging period has ended

thereby lengthening the service

life of the battery

IMPORTANT:

- while charging, the charger and the

battery may become warm to touch;

this is normal and does not indicate

a problem

- do not charge at temperatures

below 0°C and over 40°C; this will

seriously damage the battery as well

as the charger

! a battery that is new or has not

been used for a longer period

does not develop its full capacity

until after approximately 5

charging/discharging cycles

- do not repeatedly recharge the

battery after only a few minutes of

operation; this may result in a

reduction of operating time and

battery efﬁ ciency

- the battery must be kept separate

from the natural environment and

should not be disposed of as normal

domestic waste (symbol 6 will

remind you of this when the need for

disposing occurs)

! prior to disposal protect battery

terminals with heavy tape to

prevent short-circuit

- if you anticipate long periods of non-

use for the tool, it is best to unplug

the charger from its power source

• On/off 7

• Changing direction of rotation 8

- when not properly set in left/right

position, switch A 2 cannot be

activated

! change direction of rotation only

when tool is at a complete

standstill

• Changing bits 9

- push bit to end position in bitholder

! do not use bits with a damaged

shank

• Automatic spindle-lock

Allows you to manually tighten or

loosen screws, when necessary 0

APPLICATION ADVICE

• Use the appropriate bits !

! do not use damaged bits

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 2148 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 2148 Manual

Product: