591172
7
Zoom out
Zoom in
Previous page
1/100
Next page
7
Before use, thoroughly inspect the cutting area and
remove any object that the tool may sling during cutting
(such as stones, loose pieces of wood, etc.)
DURING USE
Only use the tool in an vertical position, with the brush
pointing to the ground (neverswitchonthetoolin
anotherposition)
Operate the tool at a walking pace only (do not run)
Do not cross roads or gravel paths with the tool still
running
Do not get distracted and always concentrate on what
you are doing
Always ensure that the ventilation openings are kept clear
of debris
AFTER USE
The brush continues to rotate for a short time after the
tool is switched o (donottouchtherotatingbrush)
Always disconnect plug from power source
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
- after striking a foreign object
- whenever the tool starts vibrating abnormally
Before you put down the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
Store the tool indoors in a dry and locked-up place, out
of reach of children
EXPLANATIONOFSYMBOLSONTOOL
3Warning! Read the instruction manual
4 Do not expose tool to rain
5 Wear protective glasses and hearing protection
6 Payattentiontotheriskofinjurycausedbyflying
debris (keep bystanders a safe distance away from work
area)
7 Always keep hands and feet away from rotating parts
8 Switch o and disconnect plug before cleaning/
maintenance or if (extension) cord is damaged or
entangled
9 Double insulation (no earth wire required)
0 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
USE
Assembly instructions
! alwaysdisconnecttheplugbeforemounting/
removingthebrush
- slide guard A over motor housing as illustrated until it
clicks into place !
- mount wheel B onto motor housing as illustrated until it
clicks into place @
- push spindle-lock button C and hold it while you
loosen collet nut D with wrench E #
- mount brush F with its centre in line with brush
indicator G
- tighten collet nut D with wrench E while pushing
spindle-lock button C
! replacethebrushwhenitisworn(SKIL
accessorynumber2610Z02973)
Height adjustment $
- loosen locking sleeve H by turning it clockwise
! whenusingtoolforthefirsttime,rotatehandleK
90°afterlooseninglockingsleeveH
- extend tube J to the desired height
- tighten locking sleeve H by turning it counter-clockwise
! donotforcethetoolwhenextending/retracting
thetubetodesiredheight
Cord restraint %
- hook the loop in the extension cord over restraint L as
illustrated
- pull tight to secure the extension cord
On/o ^
- switch on tool by pressing trigger switch M
- switch o tool by releasing trigger switch M
! afterswitchingoffthetoolthebrushcontinuesto
rotateforafewseconds
- allow the brush to stop rotating before switching on
again
! donotrapidlyswitchonandoff
Before using the tool
- ensure that brush F # is correctly mounted and that
collet nut D # is rmly tightened
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
Removing weed
! ensurethatthecuttingareaisfreeofstones,
debrisandotherforeignobjects
- ensure that the bottom side of the tool is kept in a level
position
- start working only when motor is running
- start working near the mains socket and move away
while working
- keep the tool away from solid objects and plants
- do not use the tool in one spot too long
- do not overload the tool
Holding and guiding the tool &
- hold the tool rmly with one hand
- guide the tool at a constant speed over the surface to
be worked on
- maintain a stable working position
- always hold the tool well away from your body
APPLICATIONADVICE
For best results test-run the tool on a small part of the
surface and check if the tiles do not get damaged
Regular weeding helps to avoid persistent weed
For more tips see www.skil.com
MAINTENANCE/SERVICE
This tool is not intended for professional use
Always keep tool and cord clean
! disconnecttheplugbeforecleaning
- regularly clean ventilation slots N 2 with a soft cloth
- regularly remove dirt from cutting guard A 2 with a
soft brush
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0700 in the language / languages: All languages as an attachment in your email.

The manual is 9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info