591172
6
Zoom out
Zoom in
Previous page
1/100
Next page
6

Weed brush 0700
INTRODUCTION
This tool has been designed for removing weed from
terraces and between tiles
This tool is not intended for professional use
Check whether the packaging contains all parts as
illustrated in drawing 2
When parts are missing or damaged, please contact your
dealer
• Readthisinstructionmanualcarefullybeforeuse
andsaveitforfuturereference3
• Payspecialattentiontothesafetyinstructionsand
warnings;failuretofollowthesemayresultin
seriousinjury
TECHNICAl DATA 1
TOOl ElEmENTS 2
A Cutting guard
B Wheel
C Spindle-lock button
D Collet nut
E Wrench
F Brush
G Brush indicator
H Locking sleeve
J Telescopic tube
k Handle
l Cord restraint
m Trigger switch
N Ventilation slots
P Storage rail (screwsnotsupplied)
SAFETY
SPECIFICSAFETYINSTRUCTIONSFORWEED
BRUSHES
GENERAl
Be familiar with the controls and the proper use of the tool
The user is responsible for accidents or hazards
occurring to other people or their property
Only use the tool when the ambient temperature is
between 0°C and 40°C
Never mount metal cutting elements onto this tool
Do not use the tool for removing wet weed
PERSONALSAFETY
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the tool by a person responsible for their safety
Ensure that children do not play with the tool
Never allow children or people who are not familiar with
the operating instructions to use the tool
Always wear eye protection, long trousers and sturdy
shoes when operating the tool
Never operate the tool with a damaged cutting guard or
without the cutting guard mounted
Never operate the tool in the direct vicinity of persons;
stop using the tool when persons (especially children) or
pets are nearby
Never operate the tool when you are tired, sick or under
the inuence of drugs, alcohol or medication
ElECTRICAl SAFETY
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
Inspect the cord periodically and have it replaced by a
qualied person, if damaged
Inspect the extension cord periodically and replace it, if
damaged (inadequateextensioncordscanbe
dangerous)
Only use an extension cord which is intended for outdoor use
and equipped with a watertight plug and coupling-socket
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
Do not run over, crush or pull the (extension) cord
Protect the (extension) cord from heat, oil and sharp
edges
Keep the (extension) cord away from the rotating brush
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (donottouchthecord
beforedisconnectingtheplug)
BRUSHES
SKIL can assure awless functioning of the tool only
when original accessories are used
Only mount brushes of which the maximum speed
(“RPM”) is higher than the rotations per minute marked
on the tool
Only use brushes with a maximum diameter of 100 mm
Do not use worn brushes
Rust stains or other signs of chemical or mechanical
changes of the material that hold the brush threads may
cause premature brush disfunctioning
Store brushes in a suitable place in such a way that they
are protected against the following inuences:
- high atmospheric humidity, heat, water or other uids
which could damage the brush
- acids or acid vapours, which could damage the brush
- low ambient temperatures causing condensation on
the brush when stored in an area with higher ambient
temperatures
- deformation of whatever part of the brush
BEFORE USE
Only use the tool in daylight or with appropriate articial
lighting
Check the functioning of the tool before each use and
after any impact; in case of a defect, have it repaired
immediately by a qualied person (never open the tool
yourself)
Remove any adjusting key or wrench before turning the
power tool on (awrenchorakeyleftattachedtoa
rotatingpartofthepowertoolmayresultin
personalinjury)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0700 in the language / languages: All languages as an attachment in your email.

The manual is 9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info