797782
13
Zoom out
Zoom in
Previous page
1/140
Next page
13
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK
Do not dispose of electric tools, accessories and
packaging together with household waste material
-in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
-symbol 9 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
Measured in accordance with EN 62841 the sound
pressure level of this tool is 82 dB(A) (uncertainty
K = 3 dB) and the sound power level 89 dB(A)
(uncertainty K = 4.1 dB), and the vibration < 2.5 m/s²
(triax vector sum; uncertainty K = 1.5 m/s²)
The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
-using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
-the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the eects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Taille-haie sans l 0480
INTRODUCTION
Cet outil a été conçu pour tailler les haies et les buissons
et il est destiné à un usage domestique uniquement
Cet outil n’est pas conçu pour un usage
professionnel.
Lisez attentivement ce mode d’emploi avant
d’utiliser l’outil et conservez-le pour pouvoir vous y
référer ultérieurement
Prêtez particulièrement attention aux consignes de
sécurité et aux avertissements ; sinon, vous risquez de
subir des blessures graves
Vériez que toutes les pièces montrées sur le schéma
sont contenues dans l’emballage
Lorsque des pièces manquent ou sont endommagées,
contactez votre revendeur
CARACTÉRISTIQUES TECHNIQUES 1
PIÈCES DE L’OUTIL 2
A Poignée arrière
B Bouton de blocage
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
Sharpening the cutting blades
! remove battery from tool
-sharpen the cutting blades with a small and smooth le,
in case a solid object damaged them
-we advise you, however, to have the blades sharpened
by a specialist
-lubricate the cutting blades after sharpening
Storage
-use blade cover H when storing the tool
-before storing the tool, wipe o the cutting blades with
an oil-soaked rag to prevent corrosion
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the SKIL warranty conditions see
www.skil.com or ask your dealer)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,
immediately switch o the tool and remove battery
Motor does not start or stops suddenly
-empty battery -> charge battery
-hot battery -> let battery cool down
-cutting blades jammed -> clear jammed material
-internal fault -> contact dealer/service station
Tool operates intermittently
-on/o switch defective -> contact dealer/service station
-internal wiring defective -> contact dealer/service
station
-impeller blocked by foreign object -> remove blockage
Motor runs but blades remain stationary
-internal fault -> contact dealer/service station
Cutting blades hot
-cutting blades blunt -> have blades sharpened
-cutting blades have dents -> have blades inspected
-too much friction due to lack of lubricant -> lubricate
blades
ENVIRONMENT
Only for EU countries
Do not dispose of electric tools, accessories and
packaging together with household waste material
-in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
-symbol 9 will remind you of this when the need for
disposing occurs
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0480 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0480 in the language / languages: All languages as an attachment in your email.

The manual is 6.26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info