797782
12
Zoom out
Zoom in
Previous page
1/140
Next page
12
4 levels of the battery level indicator keep solid red for
10s; wait until battery has returned within the allowable
operating temperature range qd
! do not continue to press the on/o switch after the
tool is switched o automatically; battery may be
damaged
on/o switch w
! Make sure you have a secure and balanced
footing.
-Depress and hold the front switch lever K
-Pressing the knob B
-switch on the tool by pressing the trigger switch F
-switch o the tool by releasing the trigger switch F
Operating the tool
! start trimming only when motor is running
! do not cut ground covering plants in order to
prevent earth/sand from damaging cutting blades
E
! do not overload the tool by cutting stems larger
than 20 mm in thickness
-move tool away from cutting area before switching o
! after switching o the tool ,wait for the blades to
come to a complete stop
Trimming hedges e
-trim the sides of the hedge rst (from the bottom
upwards), then cut the top
-trim the side of a hedge in such a way that it will be
slightly narrower at the top
-use a hand saw or pruning shears to cut thicker
branches
Holding and guiding the tool r
-hold the tool rmly with both hands and take a secure
stance
! while working, always hold the tool at the grip
area(s)
-guide the tool ahead of you
APPLICATION ADVICE
For trimming a hedge at a uniform height level
-fasten a piece of string along the length of the hedge at
the desired height
-trim the hedge just above this string
Recommended cutting/trimming times (Western Europe)
-trim hedges with deciduous leaves in June and October
-trim evergreen hedges in April and August
-trim conifers and other fast-growing shrubs every 6
weeks from May until October
MAINTENANCE / SERVICE
This tool is not intended for professional use
Keep tool and cutting blades clean
! remove battery from tool before cleaning
-clean the tool with a damp cloth (do not use cleaning
agents or solvents)
-clean ventilation slots G 2 regularly with a brush or
compressed air
-after use, always carefully clean and lightly lubricate the
cutting blades
! wear gloves when handling or cleaning the cutting
blades
Regularly check the condition of the cutting blades and
the tightness of the blade bolts
Always wear long trousers and long sleeves when
operating the tool
Keep other persons and animals at a distance of 5
metres when using the tool
Take a secure stance when working (do not overreach,
especially when using steps or a ladder)
In case of electrical or mechanical malfunction,
immediately switch o the tool and remove battery
AFTER USE
Store the tool indoors in a dry and locked-up place, out
of reach of children
-store the battery pack separately from the tool
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
rst time)
Only use the following batteries and chargers with
this tool
-SKIL battery: BR1*41****
-SKIL charger: CR1*41****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
-when charging 4...40°C
-during operation –20...+50°C
-during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in re, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Pay attention to the risk of injury caused by ying
debris (keep bystanders a safe distance away from work
area)
7 Wear protective glasses and hearing protection
8 Do not expose tool to rain
9 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator q
-press the battery level indicator button J to show the
current battery level qa
! when the lowest level of the battery indicator
starts ashing red for 10s after pressing button J
qb, the battery is nearly depleted.
Battery protection
The tool is suddenly being switched o or prevented from
being switched on, when
-the load is too high --> remove load and restart
-the battery is empty --> the 4 levels of the battery
level indicator starts ashing red for 10s; Remove the
battery from the tool and charge the battery qc
-the battery temperature is not within the allowable
operating temperature range of -20 to +50°C -->
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0480 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0480 in the language / languages: All languages as an attachment in your email.

The manual is 6.26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info