616322
9
Zoom out
Zoom in
Previous page
1/14
Next page
INSERTING THE BOBBIN
To insert the bobbin, first remove the bobbin cover plate.
Place the bobbin into the bobbin case.
Pull the thread tail to check that the bobbin turns in a counter-clockwise direction. If it turns
in a clockwise direction, remove it from the bobbin case, turn it over and replace it into the
bobbin case. Pull the thread tail again to ensure that it moves in a counter-clockwise direction.
THREADING THE UPPER THREAD
Threading the upper thread is a simple process, but it must be done correctly in order to
achieve the correct sewing results.
Turn the Power On/Off & Speed Control Switch to the “off” position before threading the machine.
Start by raising the needle to its highest position by turning the handwheel toward you
(counter-clockwise), and continue turning until the needle just starts to descend.
Raise the presser foot lifter, which will release the tension of the machine.
Note: This step is very important. If the presser foot is not raised so that the tension is released,
the result will be a large thread jam on the underside of the fabric when you start to sew.
Turn the handwheel toward you until the needle and take-up lever are in their highest positions.
Place the spool base, thread and spool cap onto the spool pin.
If the thread spool is smaller in size, the spool pin can remain in a horizontal position.
Note: If the thread spool has a slit on the end of it, put that end toward the right so that the
thread doesn't get caught on it while sewing.
THREADING THE UPPER THREAD
If the thread spool is larger in size, and therefore does not feed properly when it is placed
onto the spool pin horizontally, move the spool pin to the vertical position. If the vertical
position is used, loosen the spool cap slightly or completely remove it, so that it doesn't
prevent the spool from turning while sewing.
or
16
15
OFF L H
presser foot lifter
handwheel
Thread the machine with your left hand while firmly gripping the thread with your right
hand in the order shown:
3
1
2
4
5
6
1.Guide the thread through the thread guide at the top of the machine.
2.Pull the thread into the tension discs by pulling the thread down into the channel,
as shown.
3.Do a U-turn around the inside of the tab.
4.Pass the thread through the thread take-up lever from right to left.
5.Place the thread into the thread guide.
6.Pass the thread through the eye of the needle from front to back.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer Vivo -1004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer Vivo -1004 in the language / languages: English as an attachment in your email.

The manual is 4,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info