616714
25
Zoom out
Zoom in
Previous page
1/72
Next page
23
Cambio de la aguja
1. Levantar la barra de la aguja a la posición más alta girando el
volante en sentido contrario a las manecillas de un reloj.
2. Aflojar el tornillo que sujeta la aguja girándolo en sentido
contrario a las manecillas de un reloj.
3. Quitar la aguja sacándola hacia abajo.
4. Insertar la aguja nueva en la brida porta-aguja con el lado
plano hacia la parte posterior.
5. Empujar la aguja lo más arriba posible.
6. Apriete el tornillo de sujeción de aguja con el destornillador.
Siempre desconecte la máquina de la fuente
de alimentación retirando el enchufe del
tomacorriente de la pared.
Débranchez toujours. La machine de
l’alimentation électrique en retirant la che de la
prise murale.
Changement d’aiguille
1. Relevez la barre d’aiguille à sa position la plus haute en
tournant le volant vers vous (sens anti-horaire).
2. Desserrez la vis du serre-aiguille (sens anti-horaire).
3. Enlever l’aiguille en la tirant vers le bas.
4. Insérez la nouvelle aiguille dans le serre-aiguille, le côté
plat orienté vers l’arrière.
5. Pousser l’aiguille vers le haut, jusqu’ à la butée.
6. Resserrez la vis de l’aiguille à l’aide du tournevis.
Conseil utile: en plaçant un morceau de tissu sous le
pied presseur et en abaissant le pied presseur, vous
faciliterez l’opération de remplacement de l’aiguille,
et ceci évitera qu’une aiguille ne tombe dans la fente
de la plaque d’aiguille.
Consejo útil: Colocar un resto de material debajo del
prensatelas y bajar el prensatelas facilita el cambio de
aguja y evita que la aguja caiga en la ranura de la placa
de aguja.
REMARQUE: resserrez-la correctement, mais pas trop. NOTA: Apriete rmemente, pero no sobreapriete.
Changing the needle
1. Raise the needle bar to its highest position by turning the
hand wheel counter clockwise.
2. Loosen the needle clamp screw by turning it counter
clockwise.
3. Remove the needle by pulling it downward.
4. Insert the new needle into the needle clamp with the at
side toward the back.
5. Push the needle up as far as it can go.
6. Tighten the needle clamp screw with the screw driver.
Helpful Hint: Placing a scrap of fabric under the
presser foot and lowering the presser foot makes
it easier to change the needle and will preclude
dropping the needle into the needle plate slot.
NOTE: Tighten snugly, but do not overtighten.
Always disconnect the machine from power
supply by removing the plug from the electrical
outlet.
Flat
side
toward
the
back
Flat side
Côté plat
Lado plano
Lado
plano
hacia
atrás
Côté
plat
orienté
vers
l’arrière
Pin
Butée
Pasador
Needle
Aiguille
Aguja
25


Need help? Post your question in this forum.

Forumrules
1

Forum

singer-70

Reset search

  • I need to know how to oil and clean a singer sewing machine model 2282 Submitted on 28-10-2020 at 20:24

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 70 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 70 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 10,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info