634382
21
Zoom out
Zoom in
Previous page
1/30
Next page
| 19
Installation | TP10, TP22 & TP32 User Guide
Warning: Due to the limitations of NMEA0183, it is
recommended that only one talker is transmitting to the
Tillerpilot at any one time – i.e. instruments or GPS/chartplotter,
not both simultaneously! If more than one unit needs to be
interfaced to the Tillerpilot, these should be connected to the
NMEA cable via a changeover switch.
Because of the vast number of different manufacturers and models
of navigational equipment, Simrad cannot guarantee correct
operation and installation of third party equipment. Therefore,
before connecting any equipment to the Tillerpilot it is important
that the units manual is referred to with regard to interfacing via
NMEA.
Electronic interference suppression
The Tillerpilot has been designed to minimize the effects of
interference generated by the engine alternator. However,
precautions should still be taken by routing the cables away from
the engine compartment. Do not run the cables down trunking
carrying high current or radio antenna cables.
Engines with spark ignition, also some refrigerators, should be fitted
with suppressors. Your local agent should be able to advise on this
and supply suppression kits where necessary.
Auto compass calibration
Once the Tillerpilot is installed, it is necessary to calibrate the internal
compass to compensate for deviation caused by any metallic or
magnetic objects surrounding it on the vessel.
With the vessel motoring slowly (2–3 knots) in calm conditions and
the Tillerpilot in Standby mode, press the Starboard (
) key a
number of times to induce a slow, clockwise rotation of the vessel.
Then press and hold the TACK key, followed by the Port ( ) and
Starboard ( ) keys simultaneously.
The Port and Starboard LEDs will both light. Allow the vessel to
turn through a minimum of 11/4 turns (450º) in approximately two
minutes, during which time the fluxgate compass will automatically
calibrate itself.
STBY
TACK
STBY
AUTO
TACK
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad TP10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad TP10 in the language / languages: English as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Simrad TP10

Simrad TP10 User Manual - German - 30 pages

Simrad TP10 User Manual - Danish - 30 pages

Simrad TP10 User Manual - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info