39209
77
Zoom out
Zoom in
Previous page
1/122
Next page
Installation
20220760L 75
Power connection
There is no power cable supplied for the Transceiver. Use a
cable with minimum wire gauge of 1.5mm
2
(AWG14). The outer
diameter should be 10 mm (0,4”) to ensure a tight fit through the
gasket.
Connect the Power cable to TB1 on the IS15 Transceiver PCB
and the other end to a circuit breaker.
The connection is polarity protected and monitored by a green
LED. If a red LED is lit on the PCB, swap the supply wires (see
Figure 6-16).
6.10 IS15 Instruments as NMEA repeaters
Figure 6-20, Figure 6-21 and Figure 6-22 are examples of how
IS15 instruments can be used as NMEA repeaters. Depth, speed
and temperature can be displayed when connected to a Simrad
CEXX Chart plotter/Echo sounder or CAXX Multifunction
radar. Any preferred combination of instruments can be used, the
IS15 Combi for example is an excellent display also for wind
data presentation.
Installing the Roblink Power Cable
The configuration in Figure 6-20 is limited to a total of 3
instruments and a Roblink Power Cable (P/N 22093587) is
required to enhance the Roblink signals. Connect the cable to a
circuit breaker. Extend the cable if necessary using a wire gauge
of 0,75 mm
2
(AWG18).
Notes !
1. If an IS15 Wind Transducer is connected to the IS15
instruments when using this configuration, it must
be
plugged into connector no. 2 (Roblink) on instrument head
no. 3. Refer to note 2 for NMEA connection.
2. If only a single instrument is installed (Figure 6-22) there is
no need for the Roblink Power Cable. Simply cut the 0,3 m
(1’) cable that comes with the instrument in two and extend
the halves to the 12V supply and the NMEA source
respectively using twisted pair cable. – Also refer to
instructions for Roblink turn-off (paragraphs 7.3 or 7.13.)
77


Need help? Post your question in this forum.

Forumrules
1

Forum

simrad-is15

Reset search

  • Simrad is15 multi???
    How do u convert display depth meters to feet?
    Help Submitted on 17-6-2023 at 13:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad IS15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad IS15 in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Simrad IS15

Simrad IS15 User Manual - German - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info