23320
13
Zoom out
Zoom in
Previous page
1/108
Next page
FS 20/25 Operators Manual 901-10037001/1.1
System Familiarization Page 1.
5
Kongsberg Simrad Mesotech Ltd.
Port Coquitlam, BC - Canada
1.1.3 Display Monitor
The display monitor for the FS 20/25 HP PC processor can be either a VGA “CRT”
or LCD Simrad ruggedized monitor, but any commercially available monitor may be
used. In order to have the full benefit of high resolution provided by the video Multi-
Display adapter available with the FS processors, you should use a Simrad LCD
Monitor.
1.1.4 Processor Unit
The FS 20/25 Series HP PC is the control unit for the system. The installed FS
20/25 system software processor provides a mechanism for the sonar head
detection, setup and operation. It is operated through the Main Control panel to
enable the Sonar selection, tilt, range, gain, cursor, and by moving the mouse
pointer over the toolbar will allow the operator to perform certain operations with a
simple mouse click. A Remote Keypad is also available to simplify the operation of
the system.
The sector heading and width are also controlled by a single mouse click used to set
the center of the area to be scanned and the width of the sector scan, up to 360°, in
the polar mode.
The rear panel of the HP PC contains the connectors for AC power, Dual Monitor
port, or output for VCR recording, Serial A, Serial B port, Keyboard, Mouse, and
Printer, and Network port. The Network port can be used to connect the remote
workstation. Note: A security key (or “dongle”) must be attached to the parallel port
to enable full operation of the system.
1.1.5 Power Supply/TTM Interface Module
The FS 20/25 power supply assembly provides the high voltage required by the trawl
sonar. The DC output voltage is combined with the telemetry signals, and supplied
to the trawl sonar.
The long line power supply voltage and current are monitored by a voltage and
current meter, a selector switch located below the voltage meter can be used to
select the output voltage of the power supply required for the appropriate system
configuration. Also, a separate on/off switch is located in the front panel. Note: The
main on/off switch and fuse are located on the rear panel of the TTM Module.
The TTM assembly is the interface that provides translation between the PC serial
port and the sonar telemetry communication protocol.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad FS20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad FS20 in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info