634489
20
Zoom out
Zoom in
Previous page
1/36
Next page
18
|
Connect power | Broadband 3G/4G™ Radar Installation Guide
Connect power
The Broadband Radar can operate on 12 or 24 V DC systems. The Broadband Radar requires +V
DC to be applied on the yellow power on wire in order to operate. This can be achieved in one
of three ways:
1. Common the red and yellow wire together, and connect to a fused switch. Radar will power on
in standby when power is applied. When switch is o , radar will draw no power
2. Use ignition or install a switch that will provide power to the yellow wire. (It is recommended to
use a 5 amp fuse or breaker). The radar will turn on when switch is activated. When the switch
is o , the radar will draw minimal power (~1mA)
3. Connect the yellow wire to external wake up of suitable display such as NSE, NSO, or NSS. The
radar will turn on when the display is turned on. The display must be set to ‘Master’ under
Power Control. When the display is o , the radar will draw minimal power (~1mA)
Before connecting power to the system:
make sure the scanner has been installed and is secured.
make sure the radar interconnection cable is connected to the radar.
if using the Radar Interface Box make sure all connections have been made
to the display.
For systems using an RI10 radar interface box:
Connect the red wire to power positive 12 or 24 V DC. Use a 5 amp fuse or breaker
Connect the yellow wire to power source that will turn on the system (see above)
Connect the black wire to power negative
Red
Yellow
Black
12 -24 V DC (+)
BATT (-)
5A
For systems not using radar interface box (Lowrance 3G USA only):
Connect the red wire to power positive 12 or 24 V DC. Use a 5 Amp fuse
Connect the yellow wire to power source that will turn on the system (see above)
Connect the black wire to power negative
Data
Red
5A
Yellow
12-24 V DC +
Black
Shield
Battery (-)
No connect
Network to display
6
!
!
!
RADAR_3G_4G_IG_988-10113-003_EN_P.indd 18 2/11/2011 6:09:09 p.m.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Simrad Broadband 3G Radar at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Simrad Broadband 3G Radar in the language / languages: English as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info