614542

Silvercrest SNMD 33 A1 - IAN 114196 Manual

85
Zoom out
Zoom in
Previous page
1/94
Next page
GB / IE 85
Buttonhole foot
Preparation:
Note:
To prepare the fabric:
Tips:
Remove the presser foot and attach the
buttonhole foot (d). Adjust the stitch length dial (5)
to between "0.3" - "1". The density of the stitch
depends on thickness of the fabric.
Always test sew a buttonhole.
Measure the diameter of the button and add
0.3cm (1/8") for the bartacks. If you have a very
thick button, add more to the diameter
measurement. Mark the position and length of
the buttonhole on the fabric. Raise the needle to
its highest position.
Position the fabric so that the needle is on the
mark that is furthest from you.
Push the buttonhole foot (d) towards you as far
as it will go. Lower the foot.
A. Turn the stitch selector dial (7) to " ". Sew at
moderate speed until you reach the end mark.
Raise the needle to its highest position.
B. Turn the stitch selector dial (7) to " " and
sew 5-6 bar tack stitches. Raise the needle to
its highest position.
C. Turn the stitch selector dial (7) to " " and
sew the left side of the buttonhole to the mark
at the end which is further from you. Raise the
needle to its highest position.
D. Turn the stitch selector dial (7) to " " and
sew a few bar tack stitches. Raise the needle
to its highest position.
Lift the foot. Remove the fabric from under the
foot and separate the threads. Draw the upper
thread through the fabric to the ear and knot the
upper and lower threads. Cut the centre of the
buttonhole with the stitch ripper (n), being careful
not to cut the stitches on either side.
- Slightly reduce upper thread tension (3) to
produce better results.
- It is recommended that you use a backing
material such as yarn or fleece for fine, stretchy
or knitted fabrics. The zigzag stitch must sew
over the yarn (E).
Stitch Stitch width Stitch length
50.3~1
Sewing basics
AB CD
E
0.3
Stitch length
… 85 …


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-snmd-33-a1---ian-114196

Reset search

  • Is it possible to get a duplicate copy of the instruction manual for this machine? Mine was accidentally thrown out. Is there an address or telephone number who I can contact
    Thank you Submitted on 28-1-2018 at 17:20

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SNMD 33 A1 - IAN 114196 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SNMD 33 A1 - IAN 114196 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info